To Next Page
R
Rebecca SteeleSep 10, 2025
What to do if my TSC Printer can’t download files to memory?
- AAlison DiazSep 10, 2025
If your TSC Printer is not downloading the file to memory (FLASH / DRAM/CARD), delete any unused files in the memory.
What to do if my TSC Printer can’t download files to memory?
If your TSC Printer is not downloading the file to memory (FLASH / DRAM/CARD), delete any unused files in the memory.
How to improve print quality on a TSC Printer?
If you are experiencing poor print quality with your TSC Printer, consider the following: * Reload the supply. * Clean the print head and platen roller. * Adjust the print density and print speed. * Run a printer self-test and check the print head test pattern for missing dots. * Change to a proper ribbon or label media. * Adjust the printhead pressure adjustment knob. * Ensure the release lever latches the printhead properly.
Why is my TSC MH341T Printer not printing anything on the label?
If your TSC Printer is not printing on the label, follow these steps: * Load the media and ribbon according to the instructions. * Verify the ribbon is properly installed with the inked side facing the correct direction. * Calibrate the gap/black mark sensor.
How to fix a paper jam on a TSC MH341T Printer?
If your TSC Printer shows a 'Paper Jam' error, try the following: 1. Calibrate the media sensor. 2. Set the correct media size. 3. Remove any stuck labels from inside the printer mechanism.
Why is my TSC MH341T skipping labels when printing?
If your TSC Printer is skipping labels when printing, take these steps: * Check if the label size is set up correctly. * Calibrate the sensor using Auto Gap or Manual Gap options. * Clear the GAP/Black mark sensor with a blower.
How to troubleshoot a TSC MH341T when the power indicator is off?
If your TSC Printer's power indicator is not illuminating, please check the following: * Ensure the power cord is properly plugged into both the printer and the outlet. * Make sure the printer is switched on.
Why is the RTC time incorrect on my TSC MH341T after reboot?
To correct an incorrect RTC time after rebooting your TSC Printer, check if there is a battery on the main board.
What to do if my TSC MH341T Printer keeps taking the label?
If the TSC Printer continues to 'Take Label', check the following: * If the peeler module is installed, remove the label. * Switch off the printer and reinstall it. * Check if the connector is plugged in correctly.
How to resolve irregular printing on a TSC MH341T?
If your TSC Printer is printing irregularly, you can try: * Turning the printer off and on to skip the dump mode. * Re-setting the Rs-232 setting.
What to do when my TSC MH341T Printer says 'No Ribbon'?
If your TSC Printer indicates 'No Ribbon', you should: * Supply a new ribbon roll. * Reinstall the ribbon, referring to the steps in the user’s manual.
General| Print Technology | Thermal Transfer / Direct Thermal |
|---|---|
| Processor | 32-bit RISC CPU |
| Operating Temperature | 41°F to 104°F (5°C to 40°C) |
| Print Resolution | 300 dpi |
| Print Speed | Up to 10 ips |
| Max. Print Width | 4.09 inches |
| Interface | USB 2.0, RS-232, Ethernet |
| Power Supply | 100-240V AC, 50-60Hz |
| Storage Temperature | -40°F to 140°F (-40°C to 60°C) |
| Humidity | 25-85% non-condensing |
Detailed technical specifications and features of the MH241 Series printers, including resolution, speed, and dimensions.
Step-by-step guide for physically setting up the printer, including placement and power/data connections.
Visual instructions for correctly loading a ribbon onto the printer's supply spindle.
Guides on preparing and placing a media roll onto the printer's label supply spindle.
How to adjust print head pressure to ensure optimal print quality based on media width.
Explains the ribbon tension adjustment knob and its settings for improving print quality.
Guidance on adjusting printer parts to prevent ribbon wrinkles for better print output.
Function to check print head health, set failure thresholds, and monitor print head condition.
Details the settings and options available under the TSPL command set for printer configuration.
Details the settings and options available under the ZPL2 command set for printer configuration.
Guide to calibrating the printer's media sensors (Gap, Black Mark, Continuous) for accurate media detection.
Tools for diagnosing printer issues, including self-tests, print head checks, and sensor diagnostics.
