What to do if I can’t download files to my TSC Barcode Reader's memory?
If you can’t download the file to memory (FLASH / DRAM/CARD) of your TSC Barcode Reader, it is possible that the memory is full. Delete any unused files from the memory to free up space.
How to improve print quality on a TSC printer?
If you're experiencing poor print quality on your TSC printer, consider these solutions: * Reload the supply. * Clean the print head and platen roller. * Adjust the print density and print speed. * Run a printer self-test and check the print head test pattern for missing dots. * Change to a proper ribbon or label media. * Adjust the printhead pressure adjustment knob. * Ensure the release lever properly latches the printhead.
What to do when my TSC MB340T Printer says 'No Ribbon'?
If your TSC printer indicates 'No Ribbon': * Supply a new ribbon roll. * Refer to the user’s manual for instructions on reinstalling the ribbon.
What to do if my TSC Barcode Reader says 'No Paper'?
If your TSC Barcode Reader shows 'No Paper', it might be due to an empty label roll. Replace it with a new one. If that's not the issue, the label roll might be installed incorrectly. Refer to the user’s manual to reinstall the label roll correctly. Also, the gap/black mark sensor may not be calibrated; try calibrating it.
What to do if my TSC Barcode Reader displays 'No Ribbon'?
If your TSC Barcode Reader displays 'No Ribbon', it could be that the ribbon roll is depleted. Replace it with a new ribbon roll. Alternatively, the ribbon might be installed incorrectly. Consult the user’s manual for instructions on how to reinstall the ribbon correctly.
How to fix a TSC Barcode Reader when the power indicator does not illuminate?
If the power indicator on your TSC Barcode Reader does not illuminate, first check if the power cord is properly connected to both the printer and the outlet. If it is, ensure that the power switch is turned on.
Why is my TSC Barcode Reader not printing?
If your TSC Barcode Reader isn't printing, first ensure the interface cable is securely connected; if not, reconnect it or try a new cable. For wireless or Bluetooth connections, try resetting the wireless device settings. Also, verify that the correct printer port is selected in the Windows driver. Another solution is to clean the printhead. If none of these work, turn off the printer and check the printhead's harness connector to ensure it's properly connected. Finally, check your program to ensure there's a PRINT command at the end of the file and that each command line ends with CRLF.
Why is there no print on the label from my TSC Barcode Reader?
If your TSC Barcode Reader isn't printing on the label, make sure the label or ribbon is loaded correctly by following the instructions. Ensure that you are using compatible ribbon and media. Verify the ribbon-inked side. Also, check that the print density setting is correct.
How to correct the printing position of small labels on a TSC printer?
If the printing position of a small label is incorrect on your TSC printer: * Calibrate the sensor sensitivity again. * Set the correct label size and gap size. * Press [Menu] [Setting] [Shift Y] to fine tune the parameter of Shift Y. * If using BarTender software, set the vertical offset in the driver.
What to do if my TSC MB340T Printer shows 'No Paper'?
If your TSC printer indicates 'No Paper', you should: * Supply a new label roll. * Refer to the user’s manual for instructions on reinstalling the label roll. * Calibrate the gap/black mark sensor.
Guide to configuring the printer's Ethernet settings using a USB connection.
Guide to configuring the printer's Ethernet settings using an RS-232 connection.
Guide to configuring Ethernet settings directly over the network connection.
Configuration options for TSPL programming language, including speed and density.
Configuration options for ZPL2 programming language, including density and print speed.
Procedures for calibrating media sensors for accurate printing.
Configuration options for the RS-232 serial port, including baud rate and parity.
Settings for the printer's Ethernet module, including IP and DHCP options.
Configuration options for Wi-Fi connectivity, including SSID, security, and password.
Settings for the printer's Bluetooth module, including local name and ping code.
Settings for language, display, security, cutter, warnings, and printer care.
Using diagnostic functions to check configuration, print head, display, and sensors.
Guide to identifying and resolving common operational problems with the printer.
Instructions for cleaning printer parts like the print head and platen roller.
To Next Page
General
