Why is the LCD panel dark but the LEDs are lit on my TSC TTP-368MT Printer?
If the LCD panel is dark but the LEDs are lit on your TSC Printer: * Turn OFF and ON the printer again. * Initialize the printer.
Why is my TSC TTP-368MT not printing anything on the label?
If your TSC Printer is not printing on the label, consider the following: * Ensure the label and ribbon are loaded correctly, following the loading instructions. * Verify that the ribbon and media are compatible. * Reload the ribbon, ensuring the inked side is correct. * Clean the printhead. * Check that the print density setting is correct.
How to fix poor print quality on my TSC Printer?
To resolve poor print quality on your TSC Printer: * Reload the ribbon and media. * Clean the print head and platen roller. * Adjust the print density and print speed. * Run a printer self-test to check the print head test pattern for missing dots. * Change to a proper ribbon or label media. * Adjust the printhead pressure adjustment knob.
What to do if my TSC TTP-368MT says 'No Paper'?
If your TSC Printer indicates 'No Paper', consider these solutions: * Supply a new label roll. * Reinstall the label roll, referring to the user manual for guidance. * Calibrate the gap/black mark sensor.
Why is the LCD panel dark and LEDs are lit, but the label is feeding forward on my TSC TTP-368MT?
If the LCD panel is dark and LEDs are lit, but the label is feeding forward on your TSC Printer, the LCD panel harness connector may be plugged upside down.
What does it mean when the Power and Error LEDs are blinking fast on my TSC TTP-368MT?
If the Power and Error LEDs are blinking fast on your TSC Printer, turn off the printer and wait until all LEDs are dark, then turn the printer on again.
What does 'Carriage Open' mean on my TSC TTP-368MT?
If your TSC Printer displays 'Carriage Open', please close the print carriages.
Why is the peel sensor not working on my TSC TTP-368MT?
If the peel sensor is not working on your TSC Printer: * Ensure that the media goes through the Peel sensor. * Plug the connect cable correctly.
Why is the left side printout position incorrect on my TSC Printer?
If the left side printout position is incorrect on your TSC Printer: * Set the correct label size. * Fine-tune the Shift X parameter by pressing [MENU] [SELECT] x 3 [DOWN] x 5 [SELECT].
Why is my TSC TTP-368MT Printer printing a gray line on blank labels?
If your TSC Printer is printing a gray line on blank labels, clean the print head and the platen roller.
Provides a general introduction to the TSC bar code printer and its key capabilities.
Details the standard and optional features offered by the printer models.
Presents the printer's physical, power, environmental, and print-related specifications.
Outlines the specifications for media types, widths, and lengths supported by the printer.
Guides users through the initial unpacking and inspection process of the printer.
Provides a visual overview of the printer's front, interior, and rear component locations.
Explains the printer's control panel, including LEDs, touch screen, and physical keys.
Step-by-step instructions for physically setting up and connecting the printer.
Detailed guide on how to properly load the ribbon into the printer for printing.
Instructions for loading various media types, including roll labels and fan-fold media.
Guidance on adjusting print head pressure for optimal print quality and wrinkle prevention.
Methods for fine-tuning printer mechanisms to prevent ribbon wrinkles during operation.
How to access the printer's main menu via control panel keys or the touch screen interface.
A guide to the main menu categories and their respective configuration settings.
Procedures for calibrating and configuring the printer's media sensors for accurate media detection.
Instructions for setting up printer communication interfaces like Serial and Ethernet for connectivity.
Instructions on how to launch and begin using the TSC Diagnostic Utility software.
Details the various functions available within the diagnostic tool for printer management and testing.
Guides on configuring Ethernet settings using the diagnostic utility via USB, RS-232, and Ethernet interfaces.
Resolving problems related to power, carriage open, and general printing failures.
Solutions for poor print quality, wrinkles, incorrect positioning, and media feed problems.
Troubleshooting problems with sensors, LCD panel, ribbon sensors, and communication interfaces.
Detailed methods for cleaning the print head, platen roller, and other printer parts for longevity.
Recommended intervals for cleaning and maintaining various printer components for optimal performance.
General| Print Technology | Thermal Transfer |
|---|---|
| Print Resolution | 203 dpi |
| Media Thickness | 0.06 mm (0.00236") ~ 0.28 mm (0.011") |
| Media Core Diameter | 25.4 mm (1") ~ 76.2 mm (3") |
| Interface | USB, Ethernet |
| Operating Temperature | 5 ~ 40°C (41 ~ 104°F) |
| Operating Humidity | 25 ~ 85% non-condensing |
| Certifications | CE, FCC |
| Label Thickness | 0.06 - 0.25 mm |
| Operating System Compatibility | Windows |
To Next Page
