Tuthill M-D Pneumatics 7021 - 15 Tool Drawings

44
15. TOOL DRAWINGS
FIGURE 20 — 3200C SEAL PRESSING TOOL (T32018-1)
FIGURE 24 — 3200C/4000C/5500C GEAR AND EP TOOL (T29603)
FIGURE 21 — 3200C SEAL PRESSING TOOL (T32018-2)
FIGURE 22 — 4000C/5500C SEAL PRESSING TOOL (T11449-1)
FIGURE 23 — 4000C/5500C SEAL PRESSING TOOL (T11449-2)
NOTE: All dimensions are shown in Inches and millimeters.
3.25
82.6
.25
6.3
1.50
38.1
.75
19.02
2 REF
50.8
0.44 REF
11.17
R 0.22 (5.58) TYP
1
25.4
0.5
12.7
5.25
133.35
2.63
66.80
1
25.4
MATL P/N: CR1026T0-250050 × 1.75 (44.5) LG
MATL: COLD ROLLED 1026 TUBE,
2.50 (65) OD × .50 (15) WALL × 1.75 (45) LONG
TOOL ASSEMBLY FOR END PLATE
LAB SEAL, END PLATE
LIP SEAL AND END PLATE
MECHANICAL SEAL INSTALLATION
MATL P/N: CR1026T0-350050 × 3.25 (82.55) LG
MATL: COLD ROLLED 1026 TUBE
3.50 (88.9) OD × .50 (12.7) WALL × 3.25 (82.55) LONG
MATL P/N: CR1026T0-287075 × 4.25 (107.95) LG
MATL: COLD ROLLED 1026 TUBE
2.875 (73.025) OD × 4.25 (107.95) LONG
NOTE:
TOOLS T11449-1 & T11449-2 ARE USED TO INSTALL MECHANICAL SEAL AND
LABRYINTH SEAL USED ON MODEL 5500 ROTOR SHAFTS.
MECHANICAL SEAL USED ON MODEL 5500 DRIVE SHAFTS AND MECHANICAL
SEAL USED ON MODEL 4000 VACUUM BOOSTER DRIVE SHAFT.
MATL P/N: CR1018B0-200075 × 5.50 LG
MATL: COLD ROLLED 1018 BAR,
2.75 (69.85) × 5.5 (139.7) LONG
TOOL ASSEMBLY FOR
DRIVE SHAFT MECHANICAL
SEAL INSTALLATION
TOOL ASSEMBLY FOR END
PLATE LAB SEAL AND END
PLATE MECHANICAL SEAL
INSTALLATION
SNAP-ON P/N
CJ66-16-3 OR
EQUIVALENT
SNAP-ON P/N
CJ83-3 OR
EQUIVALENT
TOLERANCES:
FRACTIONAL = ± .0005 (0.0127)
CHAMFERS = ± 2°
TOLERANCES:
.XX = ± .01 (0.254)
.XXX = ± .0005 (0.0127)
CHAMFERS = ± 2°
.74
18.8
.50
12.7
Ø 1.872 ± .001
47.55 ± .03
Ø 1.885 ± .001
47.55 ± .03
Ø 0.69 (17.52)
3/4-16UNF-2B
Ø 2.044 ± .001
51.90 ± .03
Ø 2.50
63.5
Ø 2.25
57.1
.05 × 30°
1.0
.06 × 45°
1.5
MIN R
MIN R
MIN R
.002 (.05)
A
Ø 3.151 ± .001
80.035 ± .025
.002 (.05)
A
Ø 2.757 ± .001
70.028 ± .025
.002 (.05)
A
-A-
Ø 1.38 REF
35.05
4.00
101.6
.25
6.35
.12 × 45°
3.048
.05 × 30°
1.27
MIN R
MIN R
Ø 2.50
63.5
Ø 3.50
88.9
3.00
76.2
1.12
28.448
.835
21.209
Ø 2.746 ± .001
69.748 ± .025
MIN R
Ø 3.147 ± .001
79.933 ± .03
-A-