U-Line H-1115 User Manual

PAGE 7 OF 30 1119 IH -1114
WEIGHT TOTALIZING CONTINUED
3. When scale stabilizes, UNIT WEIGHT displays the total
number of additions.
4. After 3 seconds, scale returns to weighing mode.
CLEAR ALL TOTALIZED VALUES
Press MC to clear all of the totalized values. " " next
to M+ icon on QUANTITY display switches off. Totals for
weight, number of additions and quantity reset to zero.
NOTE: All totals will be lost if the scale is
switched off.
CALIBRATION
AUTO CALIBRATION
You must use calibration weights to accurately calibrate
the scale. Calibration weights totaling at least 10% of
scale’s capacity must be used for accurate calibration.
NOTE: Calibration weights are sold separately.
See uline.com for details.
1. With the scale displaying "0," press and release
• and UNIT WEIGHT PRESET keys simultaneously. After
approximately five seconds, the WEIGHT display
flashes the scale capacity.
2. Place weights on the scale equal to the full load
capacity. When scale stabilizes, press the MC key.
3. While the scale counts down to 0, remove the
weights from the scale. The calibration is complete.
4. Press CE to exit from the calibration mode.
NOTE: If weights equalling the full load are not
available, you can enter a weight that is less
than the full load.
5. With the scale displaying "0," press and hold
.
, then
press UNIT WEIGHT PRESET until the WEIGHT display
flashes the scale capacity. Release the keys.
6. Enter the weight to be used, then place the weight
on the scale. When the scale stabilizes, press the MC
key.
7. While the scale counts down to 0, remove the
weights from the scale. The calibration is complete.
8. Press CE to exit from the calibration mode.
RECALL THE ORIGINAL CALIBRATION VALUES
1. Press and hold CE, then press UNIT WEIGHT PRESET
until the scale counts down to 0. Release the keys.
The scale will revert to the original factory calibration
values.
UNIT WEIGHT PRESET MEMORY
The scale can store 10 sets of unit weight presets in the
number keys (0-9). Once saved, pressing a particular
number key will display the unit weight saved in that
memory.
NOTE: The UNIT WEIGHT PRESET key is a dual
function key. Determine if unit weight preset
is set as the main function or the secondary
function of this key. If unit weight preset is the
secondary function, hold the UNIT WEIGHT
PRESET key down for three seconds to activate
the feature.
SETTING A UNIT WEIGHT PRESET
1. Use the number keys (0-9) to enter the unit weight
value you wish to save.
2. Press UNIT WEIGHT PRESET.
3. Press UNIT WEIGHT PRESET again.
4. Press any number key (0-9) to save the weight in that
key’s memory.
USING THE SCALE CONTINUED
NETNET
→ 0←
WEIGHT UNIT WEIGHT QUANTITY
SMPL
WT
PC
WT
M+
STABLE
Pcs
118.3 01
NETNET
→ 0←
WEIGHT UNIT WEIGHT QUANTITY
SMPL
WT
PC
WT
M+
STABLE
Pcs
118.3 00
NETNET
→ 0←
WEIGHT UNIT WEIGHT QUANTITY
SMPL
WT
PC
WT
M+
STABLE
Pcs
5011500.0
NETNET
→ 0←
WEIGHT UNIT WEIGHT QUANTITY
SMPL
WT
PC
WT
M+
STABLE
Pcs
0.0 0100
NETNET
→ 0←
WEIGHT UNIT WEIGHT QUANTITY
SMPL
WT
PC
WT
M+
STABLE
Pcs
PrSEt
NETNET
→ 0←
WEIGHT UNIT WEIGHT QUANTITY
SMPL
WT
PC
WT
M+
STABLE
Pcs
PrSEt SEt
NETNET
→ 0←
WEIGHT UNIT WEIGHT QUANTITY
SMPL
WT
PC
WT
M+
STABLE
Pcs
0.0 0100

U-Line H-1115 Specifications

General

Brand	U-Line
Model	H-1115
Category	Scales
Language	English