How to fix Uniden Scanner that won’t work?
If your Uniden Scanner won’t work, here are a few things to try: 1. Make sure the AC adapter is securely connected at both ends. 2. Ensure the wall outlet is switched on, as it might be controlled by a wall switch. 3. Try plugging the AC adapter into a different wall outlet.
How to improve Uniden BC780XLT Scanner reception?
If you are experiencing improper reception on your Uniden Scanner: 1. Check the antenna connection and reposition the antenna to improve signal. 2. Try moving the scanner to a different location. 3. Consider that you may be in a remote area, which might require an optional multi-band antenna. Consult with your dealer or a local electronics store for antenna options.
Why won’t my Uniden BC780XLT track?
If your Uniden Scanner won’t track: 1. Ensure the system is compatible with your scanner's tracking capabilities and press and hold TRUNK for 2 seconds to enter trunk mode. 2. Verify you have the correct data frequency. 3. Consider changing to a Type 1 Scanner setup.
What to do if Uniden BC780XLT Scanner weather scan won’t work?
If your Uniden Scanner Weather Scan won’t work: 1. Adjust the squelch threshold. 2. Check the antenna.
Why am I missing replies to conversations on my Uniden Scanner?
If you are missing replies to conversations on your Uniden Scanner: 1. Change to a Type 1 Scanner setup. 2. Try another Preset Fleet Map or Program your own Fleet Map. 3. Check to see that all of the system's frequencies have been entered.
Why is my Uniden Scanner not tracking EDACS system properly?
If your Uniden Scanner is not tracking an EDACS system properly: 1. Ensure that the logical channel numbers (frequencies) for the system are programmed in the correct order. Double-check your frequency resources and reprogram if necessary. 2. Verify that all frequencies for the system are programmed. Check your frequency resources to ensure completeness.
Why won’t my Uniden Scanner stop scanning?
If your Uniden Scanner won’t stop scanning: 1. Adjust the squelch threshold. 2. Check the antenna connection. 3. Make sure that not too many channels are locked out. The scanner has less chance of finding an active channel if many are locked out. 4. Review each channel's frequency to ensure it is still stored in memory and is correct. 5. It's possible that none of the programmed frequencies are currently active.
What to do if Uniden BC780XLT will not acquire data channel?
If your Uniden Scanner will not acquire data channel: 1. Adjust the squelch for trunking mode. 2. Ensure you have the correct frequency used for the data channel. Check your frequency list.
What to do if Uniden BC780XLT Scanner scan won’t start?
If your Uniden Scanner won’t start scanning: 1. Press the SCAN key again. 2. Adjust the SQUELCH control. 3. Check to see if all channels are locked out.
Why won’t my Uniden Scanner stop during scan list mode?
If your Uniden Scanner won’t stop during Scan List mode: 1. Ensure that IDs have been programmed. 2. Check to see if the IDs you have stored are active.
General| Channels | 1000 |
|---|---|
| Modulation Types | AM, FM, WFM |
| Display | LCD |
| Power Supply | 13.8 VDC |
| Bands | VHF, UHF |
| Scan Rate | 100 Channels per second |
| Search Rate | 100 steps per second |
| Memory Banks | 10 |
| Selectivity | 70 dB |
| Type | Base/Mobile |
| Memory | 1000 Channels |
| Step Size | 5 kHz |
| Antenna | BNC |
Steps to power on the scanner and initial scanning behavior.
Procedure for adjusting the squelch control for optimal reception.
Step-by-step guide to entering frequencies into scanner channels.
Configuring frequency ranges for scanning and discovering new stations.
Storing frequencies into banks for tracking trunked systems.
Choosing the correct trunking system type (Motorola, EDACS, LTR).
Manually entering IDs into scan lists for organized trunk tracking.
Information on how the scanner tracks EDACS trunked systems.
Critical steps for programming EDACS frequencies in the correct order.
Details on Motorola Type I and Type II trunking systems.
Setting up fleet maps for Motorola Type I/Hybrid systems.
Automatically loading frequencies from a database via PC or modem.
Programming and controlling the scanner remotely via PC.
To Next Page
