Vacon CX - Page 17

Vacon Plc Phone: +358-(0)201 2121 Fax: +358-(0)201 212 205
Service: +358-40-8371 150 E-mail: vacon@vacon.com
Page 16
VV
VV
V
aconacon
aconacon
acon
Multi-purpose Control Application IIMulti-purpose Control Application II
Multi-purpose Control Application IIMulti-purpose Control Application II
Multi-purpose Control Application II
STOP
STOPSTOP
STOP
STOP
STOPSTOP
STOP
Group 5, Prohibit frequency parameters Group 5, Prohibit frequency parameters
Group 5, Prohibit frequency parameters Group 5, Prohibit frequency parameters
Group 5, Prohibit frequency parameters
Code Parameter Range Step Default Custom Description Page
5
. .
. .
. 1 Prohibit frequency 0—f
max
0.1 Hz 0 Hz 33
range 1 low limit (1
..
..
. 2)
5
..
..
. 2 Prohibit frequency 0—f
max
0.1 Hz 0 Hz 0 = Prohibit range 1 is off 33
range 1 high limit (1
..
..
. 2)
5
. .
. .
. 3 Prohibit frequency 0—f
max
0.1 Hz 0 Hz 33
range 2 low limit (1
..
..
. 2)
5
..
..
. 4 Prohibit frequency 0—f
max
0.1 Hz 0 Hz 0 = Prohibit range 2 is off 33
range 2 high limit (1
..
..
. 2)
5
. .
. .
. 5 Prohibit frequency 0—f
max
0.1 Hz 0 Hz 33
range 3 low limit (1
..
..
. 2)
5
..
..
. 6 Prohibit frequency 0—f
max
0.1 Hz 0 Hz 0 = Prohibit range 3 is off 33
range 3 high limit (1
..
..
. 2)
Group 6, Motor control parameters Group 6, Motor control parameters
Group 6, Motor control parameters Group 6, Motor control parameters
Group 6, Motor control parameters
Code Parameter Range Step Default Custom Description Page
6
. .
. .
. 1 Motor control mode 0—2 1 0 0 = Frequency control 33
1 = Speed control (open loop)
2 = Torque control (open loop)
6
. .
. .
. 2 Switching frequency 1—16 kHz 0.1 kHz 10/3.6 kHz Dependant on kW 34
6
. .
. .
. 3 Field weakening point 30—500 Hz 1 Hz Param. 34
1
..
..
. 11
6
..
..
. 4 Voltage at field 15 —200% 1% 100% 34
weakening point x U
nmot
6
. .
. .
. 5 U/F-curve mid 0—500 Hz 0,1 Hz 0 Hz 34
point frequency
6
. .
. .
. 6 U/F-curve mid 0—100% 0.01% 0 % 34
point voltage x U
nmot
6
. .
. .
. 7 Output voltage at 0—100% 0.01% 0 % 34
zero frequency x U
nmot
6
. .
. .
. 8 Overvoltage controller 0—1 1 1 0 = Controller is not operating 35
1 = Controller is operating
6
..
..
. 9 Undervoltage controller 0—1 1 1 0 = Controller is not operating 35
1 = Controller is operating
Note!Note!
Note!Note!
Note!
STOP
STOPSTOP
STOP
= Parameter value can be changed only when the frequency converter is stopped.
STOP
STOPSTOP
STOP
STOP
STOPSTOP
STOP
STOP
STOPSTOP
STOP
STOP
STOPSTOP
STOP
STOP
STOPSTOP
STOP