Vacon CX - Page 49

Vacon Plc Phone: +358-(0)201 2121 Fax: +358-(0)201 212 205
Service: +358-40-8371 150 E-mail: vacon@vacon.com
Page 48
VV
VV
V
aconacon
aconacon
acon
Multi-purpose Control Application IIMulti-purpose Control Application II
Multi-purpose Control Application IIMulti-purpose Control Application II
Multi-purpose Control Application II
Fieldbus controlFieldbus control
Fieldbus controlFieldbus control
Fieldbus control
Fieldbus control can be activated with parameter 10.1. Then the frequency or speed refer-
ence comes from the fieldbus as well as the Start/Stop and Reverse control.
First two parameters in group 10 concern all fieldbuses. Parameters 10.3 - 10.6 are only for
Modbus, parameters 10.7 - 10.13 only for Profibus and 10.14 only for LonWorks.
10. 110. 1
10. 110. 1
10. 1
Fieldbus controlFieldbus control
Fieldbus controlFieldbus control
Fieldbus control
Defines the active control source:
0:0:
0:0:
0: control via I/O terminals
1:1:
1:1:
1: control via Fielbus board
10.210.2
10.210.2
10.2
DIC1 functionDIC1 function
DIC1 functionDIC1 function
DIC1 function
0:0:
0:0:
0: Fieldbus control, contact open = Active control source are I/O terminals
contact closed = Active control source is the Fieldbus
board
1:1:
1:1:
1: External Fault, closing contact = Fault is shown and motor is stopped
when the input is active
Parameters 10.3 - 10.6 only for Modbus protocolParameters 10.3 - 10.6 only for Modbus protocol
Parameters 10.3 - 10.6 only for Modbus protocolParameters 10.3 - 10.6 only for Modbus protocol
Parameters 10.3 - 10.6 only for Modbus protocol
10.310.3
10.310.3
10.3
Slave addressSlave address
Slave addressSlave address
Slave address
Defines slave device address. Maximum value for this parameter is 247
and minimum is 1.
10.410.4
10.410.4
10.4
Baud RateBaud Rate
Baud RateBaud Rate
Baud Rate
1:1:
1:1:
1: 300 baud
2:2:
2:2:
2: 600 baud
3:3:
3:3:
3: 1200 baud
4:4:
4:4:
4: 2400 baud
5:5:
5:5:
5: 4800 baud
6:6:
6:6:
6: 9600 baud
7:7:
7:7:
7: 19200 baud
10.510.5
10.510.5
10.5
Parity typeParity type
Parity typeParity type
Parity type
0:0:
0:0:
0: None
1:1:
1:1:
1: Even
2:2:
2:2:
2: Odd
10.610.6
10.610.6
10.6
Modbus time-outModbus time-out
Modbus time-outModbus time-out
Modbus time-out
The Modbus time-out determines how long the Fieldbus board waits for a
message from a master device and is specified in seconds.
Time can be set between 0 - 3600 s. Time 0 s = No time-out
Parameters 10.7 to 10.13 only for Profibus DP protocolParameters 10.7 to 10.13 only for Profibus DP protocol
Parameters 10.7 to 10.13 only for Profibus DP protocolParameters 10.7 to 10.13 only for Profibus DP protocol
Parameters 10.7 to 10.13 only for Profibus DP protocol
10.710.7
10.710.7
10.7
Profibus slave addressProfibus slave address
Profibus slave addressProfibus slave address
Profibus slave address
Defines slave device address. Maximum value for this parameter is 126 and
minimum 2.