VADDIO RoboSHOT 20 UHD User Manual (English)

Other manuals for VADDIO RoboSHOT 20 UHD

Complete Manual104 pages

Integrator's Complete Guide73 pages

Questions and Answers:

H
herringjoseAug 16, 2025
What to do if VADDIO RoboSHOT 20 UHD is not working?
- M
  Molly LesterAug 16, 2025
  If your VADDIO Security Camera shows no status light, video, or response to the remote, start by checking all cables with known good ones. If using a OneLINK extension, ensure it's properly connected to the camera. If problems persist with OneLINK, bypass it by connecting the camera directly to the included 12V power pack to isolate the issue. If the camera then works, the OneLINK is faulty and you should contact your reseller or Vaddio Technical Support. Also, verify that the wall outlet is active by testing it with another device.
L
Laura JenningsAug 19, 2025
What to do if the VADDIO RoboSHOT 20 UHD Security Camera light is off?
- A
  andersondeborahAug 19, 2025
  If the light on the front of your VADDIO Security Camera is off, here are a few things to check: * Ensure all cables are working correctly by testing them with known good cables. * If using a OneLINK extension system, make sure it's properly connected to the camera. If the OneLINK system isn't working, disconnect it and connect the camera directly to the 12V power pack. If the camera then works, the OneLINK is faulty and you should contact your reseller or Vaddio Technical Support. * Verify the wall outlet is active by testing it with another device. * If none of the above steps work, the camera or its power supply might be defective.
D
Daniel MartinezAug 22, 2025
Why VADDIO RoboSHOT 20 UHD doesn't respond to the remote, but the web interface is available?
- M
  Michelle GarciaAug 22, 2025
  If your VADDIO Security Camera isn't responding to the remote but the web interface is accessible, the issue might be: * The remote is not on the same IR channel as the camera. Try pressing the Camera Select 1 button on the remote, and other Camera Select buttons if needed. * IR is disabled. Turn IR on by setting DIP switch 3 up. * The remote's batteries are dead. Replace them with new batteries.
D
Dr. John HopkinsAug 26, 2025
How to fix VADDIO Security Camera not responding to RS-232 commands, but web UI is available?
- A
  Adam GutierrezAug 26, 2025
  If the web UI for your VADDIO Security Camera is available but the camera doesn't respond to RS-232 commands, consider these solutions: * Ensure the RS-232 cable is properly connected and functioning. Try using a known good cable. * Verify that the camera's RS-232 settings match the settings on the controlling device. You can check the camera's settings on the System page in the web UI and adjust them as needed.
D
Deborah MullinsAug 28, 2025
What to do if VADDIO RoboSHOT 20 UHD responds to the remote, but the web interface is unavailable?
- P
  Patrick ClarkAug 28, 2025
  If your VADDIO Security Camera responds to the remote but the web interface is unavailable, the camera might not be using the IP address you are browsing to. Press the Data Screen button on the remote to view camera information.
G
gmaysAug 31, 2025
What to do if VADDIO RoboSHOT 20 UHD is not responding to the remote and the light is yellow?
- L
  Lisa MarksAug 31, 2025
  If your VADDIO Security Camera is not responding to the remote and the light is yellow, a firmware update may be in progress. Wait a few minutes and try again when the light turns blue.
L
Leah AllenSep 3, 2025
How to fix poor video stream quality on VADDIO RoboSHOT 20 UHD Security Camera?
- J
  Jonathan VazquezSep 3, 2025
  If the video stream displays poorly on your VADDIO Security Camera, with issues like a jagged band, it could be due to the stream requiring more bandwidth than available. Try reducing the streaming resolution.
L
Leslie MurphySep 6, 2025
Why does VADDIO RoboSHOT 20 UHD lose settings when power is cycled?
- K
  Kendra RobinsonSep 6, 2025
  If your VADDIO Security Camera loses all its settings when power is cycled, it might be because all the DIP switches are in the ON (down) position. Set the DIP switches to their proper positions; the default is all OFF (up).
K
Kevin FrenchSep 9, 2025
What to do if the VADDIO RoboSHOT 20 UHD web interface has stopped responding?
- B
  Benjamin SerranoSep 9, 2025
  If the web interface for your VADDIO Security Camera has stopped responding, reboot the camera.
H
hhernandezSep 12, 2025
How to enable H.264 video stream on VADDIO Security Camera?
- S
  Sarah RiosSep 12, 2025
  If there is no H.264 video stream from your VADDIO Security Camera, verify that streaming is enabled on the Streaming page in the web interface.

VADDIO RoboSHOT 20 UHD Specifications

General

Aspect ratio	3:2, 4:3, 16:9
Maximum frame rate	30 fps
Supported video modes	720p, 1080i, 1080p, 2160p
Video formats supported	H.264
Maximum video resolution	3840 x 2160 pixels
Supported graphics resolutions	3840 x 2160
Megapixel	9.03 MP
Sensor type	CMOS
Sync system	Internal
Digital zoom	1.67 x
Optical zoom	12 x
Combined zoom	20 x
White balance	ATW, Auto, Indoor, Manual, One push, Outdoor
Focus adjustment	Auto/Manual
Image sensor size	1/2.3 \
Minimum illumination	3 lx
Aperture number of steps	16
Auto focusing (AF) modes	Auto, Manual, One Push Trigger
Field of view (FOV) angle	72 °
Effective sensor resolution	8.93 MP
Signal-to-Noise Ratio (SNR)	50 dB
Back Light Compensation (BLC)	Yes
Horizontal field of view (tele)	4.8 °
Maximum working distance (tele)	1500 mm
Minimum working distance (wide)	10 mm
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	-5 - 60 °C
Storage relative humidity (H-H)	20 - 95 %
Operating relative humidity (H-H)	20 - 80 %
Current	3 A
DC input voltage	12 V
Pan range	-160 - 160 °
Product color	Black, Silver
Tilt angle range	-30 - 90 °
Number of persons	- person(s)
Ethernet LAN (RJ-45) ports	2
Cables included	AC
Tilt speed (min)	0.35 °/sec
Harmonized System (HS) code	85258900