What to do if the screen is dark on Valley Farm Equipment?
If the screen is dark on your Valley Farm Equipment, it might be due to the contrast being set too high or too low. Try adjusting the contrast by pressing the home key to go to the status screen, and then use the up or down arrow keys to adjust it. If that doesn't work, contact your Valley dealer.
What does error E11 mean on Valley Farm Equipment?
This error on Valley Farm Equipment indicates that the STB flash memory is corrupt. Please contact your Valley dealer for assistance.
What does error E02 mean on Valley Farm Equipment and how to fix it?
Error E02 on your Valley Farm Equipment indicates a checksum error in the EEPROM section of memory. This can occur if power is lost while entering constants, potentially resulting in data loss. Try a hard reset of the module. If the problem persists, contact your Valley dealer.
What does error E01 mean on Valley Vflex Farm Equipment and how can I resolve it?
Error E01 on your Valley Farm Equipment can be caused by an incorrect checksum in the BBRAM section of memory or weak batteries in the Real-time Clock (BBRAM). If this error occurs, replace the Real-time Clock. For further assistance, contact your Valley Dealer.
What does error E12 mean on Valley Vflex?
Error E12 on Valley Farm Equipment indicates that the EEPROM memory is corrupt, potentially due to loss of power while saving machine configuration parameters or runtime data. Contact your Valley dealer for assistance.
What does STB FLASH FAULT mean on Valley Farm Equipment?
If your Valley Farm Equipment displays 'STB FLASH FAULT', it means the memory area containing the currently running software is corrupt. Contact your Valley dealer for assistance.
Why does the screen cycle on and off on my Valley Vflex Farm Equipment?
If the screen on your Valley Farm Equipment cycles on and off, it suggests erratic incoming power. Contact your Valley dealer for assistance.
What does error E04 mean on Valley Farm Equipment?
If your Valley Farm Equipment shows error E04, it indicates a keypad failure or a stuck key. Contact your Valley dealer for assistance.
What does STB EEPROM FAULT mean on Valley Farm Equipment and how to fix it?
If your Valley Farm Equipment displays 'STB EEPROM FAULT', it means the memory area containing runtime parameters and machine configuration is corrupt. A hard reset may fix this error. If the issue persists, contact your Valley dealer.
What to do if the Valley Vflex Farm Equipment shows STB SOFTWARE error?
If you're experiencing 'STB SOFTWARE' issue with your Valley Farm Equipment, it means that the STB was restarted unexpectedly. Contact your Valley dealer for assistance.
General| Brand | Valley |
|---|---|
| Model | Vflex |
| Category | Farm Equipment |
| Language | English |
Details installation requirements for differential circuit breakers in the EU.
Explains the scope of the manual and the need to use it with other related manuals.
Clarifies owner's responsibility for warranty registration of ancillary equipment.
Explains hazard symbols, DANGER, WARNING, CAUTION messages.
Details the meaning of hazard symbols, DANGER, WARNING, CAUTION, and NOTE.
Covers PPE requirements for electrical hazards and safe handling of conductive materials.
Addresses fall hazards and the use of appropriate fall protection equipment.
Details minimum working clearance requirements around electrical panels and equipment.
Defines a qualified person and their role in working on de-energized electrical equipment.
Warns about hazards and clearance requirements when working near overhead power lines.
Establishes minimum requirements for locking out energy isolating devices during maintenance.
Provides essential tips for safe operation, including emergency stopping and component safety.
Covers various warnings and cautions for safe operation, including electrical hazards and component safety.
Explains the importance of safety decals and identifies their locations on the machine.
Describes VCS control panel components and defines key terms used in the manual.
Details component configurations for standard (trailing) and inverted (leading) corners.
Explains the main status screen display, including time, angles, speed, and solenoids.
Explains the usage of function keys for programming and viewing data.
Details the usage of numeric entry and navigation arrow keys for input and menu navigation.
Explains symbols, conventions, command prompts, and screen delay behavior.
Outlines the steps and conditions for powering on and starting the VCS control panel.
Explains how to use the Programs key for irrigation, chemigation, and override settings.
Details how to configure solenoid valve controls based on different corner angles.
Details how to configure solenoid valve controls based on different machine angles.
Explains the Retracted Psi menu for pressure regulator settings.
Provides an overview of diagnostic features for identifying and correcting VCS failures.
Lists machine shutdown faults, their descriptions, and how to view them.
Summarizes possible error codes, their descriptions, and potential causes.
Explains how error logs record error details and how to view them.
Details the system review log for status changes and associated error codes.
Details the use of analog channels for monitoring voltage feedback.
Explains how to review module status and GPS location and heading.
Lists essential precautions for safe troubleshooting and maintenance of the machine.
Lists and describes possible system faults, their causes, and corrective actions.
Details possible error codes, their descriptions, thresholds, and corrective actions.
Provides a list of common problems with their causes and corrective actions.
Details the effects and steps for performing a hard reset on the control panel.
To Next Page