Vector VEC1087C User Manual

Do not
chorge
the
bottery
while woiting
for the
engine
to
worm. This will involidote ony olternotor
check. The
digitol disploy
should show the circuloting pottern
while the
engine
is
worming.
Do
not
turn
on A/C
or
the
defroster
system to lood
the
olternotor. These
occessories moy
stort operoting
during o test
sequence
ond give
on
involid result.
GENERAI. BAITERY SATEIY
With minimol
moinlenonce, the
VEC1087C 2/6/10 AJ'A?
Smorl Bottery Chorger
will
provide yeors
of dependoble
service. Follow
these simple
steps lo mointoin the
chorger in optimum
condition:
t
After
eoch use, cleon the
bottery chorger
clomps
-
be sure lo remove ony
bottrery fluid thot will
couse
corrosion of
the
copper clomps.
.
Cleon the
ouiside
cose of fie
chorger with
o soft cloth ond, if necessory,
mild
soop solution.
o
Do nol
ollow liquid
to enter the
chorger. Do
nol operote when
chorger is wet.
.
Keep the
chorger
cords loosely
coiled during
storoge to prevent
domoge trc the
cords.
'
h Pt
u19 chgrger if
cords
or clomps hore
been
domoged in
ony
woy
-
coll Vector Technicol
Support
Deportmenl
toll-free:
(866)
584-5504
to reploce
cords
ond clomps.
-
TROUBI.ESHOOTIilG.
FAUTI
I.ED tII
The
following
conditions
moy lighlhe
FAULT
LED:
o
Poor
connection to
botteqy
(or
frome).
.
Chorging too
fost
-
Decreose
Chorge Rote
-
Press
2/6/ 10 AMp
button to lower
rote.
'
Chorging trco
slowly
-
Botcry
is lorge
ond
did not compleis
chorging in
24 hours
-
Press
2/6/ 10
AMP to
chorge
or o foster
role-
.
Shorted
bottery cell
-
Reploce
bottery
(F0i).
.
Open
bottery
Cell
-
Reploce
bottery
(F03).
o
Reverse
Polority LED
Lit
-
disconnect
AC rhen
reverse
clomp locotions
on bottery
ond frome.
o
lnternol
overheot in
chorger-
moke sure
fon is not
blocked
(F05).
Try
chorging
onother bottery
if the FAUTT
LED does
not light, then
one o[ the
obove
problems
exists with
fie initiol
botterv.
9-hgtg:r-
will_
not chorge
ond the
fon will not
operote i[
there is
o
foult.
Coli
Vector Technicol
Suppo* toll
fre!:
(866)
584-5504.
I1{IIRilA1
SHoRI
(t11
BAIIIRY
(Iot}
.
lf the bofiery
being
chorged hos
on internol
shorred
cell, the FAULT
LED will lighr.
'
lf
FAU\T
LED
light comes
on,
Veclor recommends
you
toke your
boitery to o
ceriified outomolive
service
center
IOr
evotuoflon.
BATTTRY
1{OI
AC(TMilG
A ffARGt
'
Moke
sure thot the
chorger
is
plugged
intro
o
"live"
'l
lo/l2ovAc
ou
er ond
power
LED
is lit.
t
UnPlug
chorger
ond check
bottery connections
-
ensure thol lhere
is o good
conneclion
ot
the
boHeqy terminol
ond/or
vehicle
chossis.
.
Check thot
the correct
chorge rote
wos
selected for
the bottery
being chorged.
o
Ensure thol
enough
chorging time
wos
ollowed for-check
toble in
(poge
'10)
for
opproximote
chorging times.
l{0I[:
Chorger will
NOT
operote on
botteries
below 2.0
Volts. lf
o
l2
Volt bottery
is below 2.0 vohs
ir is probobly
shorted,
open or
sulfoied ond
should
be reploced.
VTRY CO1D
BATTTRY
lf
the bottery
to be,chorged
is
extremely
cold
(in
lemperotures
less
thon freezing
-
Oo
C/32. F) it connot
occept
o high
rote
of chorge,
so
the
initiol
chorge rote will
be slow.'The rote
o[ chorge will
incieose
os fie
boffery worms.
WARNING:
DO
NOT
ATTEMPT
TO
CHARGE
A FROZEN
BATTERY

Vector VEC1087C Specifications

General

Brand	Vector
Model	VEC1087C
Category	Battery Charger
Language	English