VERITAS 5250 - Page 71

To Next Page

To Previous Page

The rail has a lock mechanism that prevents the hardware from being fully

pushed into the rack. Pull the blue tab forward to unlock the intermediate rail

and continue sliding the node into the rack.

71D Series Appliance installation procedures

Installing the appliance into a rack

Main Page

Table of Contents4
About the Appliance and the Storage Shelves8
Hardware Overview8
Appliance Disk Drives9
About the 5250 Appliance Control Panel10
About the System Status LED States12
About the Power Button LED States15
Appliance Rear Panel16
Storage Shelf Disk Drives17
Storage Shelf Control Panel18
Storage Shelf Rear Panel19
About IPMI Configuration21
Cables21
Product Documentation23
Customer-Provided Environment and Supplies24
Preinstallation Requirements24
Appliance Shipping Container Contents25
Best Practices for Rack Installation26
Storage Shelf Shipping Container Contents26
Determining Rack Locations27
Storage Shelf Rack Requirements28
Heat Dissipation29
Prerequisites for IPMI Configuration30
Verifying SAS-3 Cable Length30
Installing the Storage Shelf Rack Rails32
S Series Appliance Installation Procedures32
Installing the Storage Shelf into a Rack34
Attaching the Storage Shelf Bezel35
Installing the Appliance Rack Rails36
Installing the Appliance into a Rack40
Understanding Appliance and S Series Storage Shelf Connections41
Connecting an Appliance to One Storage Shelf44
Connecting an Appliance to more than One Storage Shelf45
D Series Appliance Installation Procedures58
Installing the Storage Shelf Rack Rails58
Installing the Storage Shelf into a Rack61
Installing the Appliance Rack Rails65
Installing the Appliance into a Rack69
Understanding Appliance and D Series Storage Shelf Connections72
Connecting an Appliance to One Storage Shelf74
Connecting an Appliance to more than One Storage Shelf75
Connecting the Network Cables82
Next Steps after Installation82
Connecting the Power Cords83
Turning on the Hardware and Verifying Operation87
Configuring the IPMI Port from the Netbackup Appliance Shell Menu98
Configuring the Veritas Remote Management Interface from a Flex Appliance102
Accessing and Using the Veritas Remote Management Interface106
Operating Appliance that Does Not Have any Storage Shelves110
Overview110
Preparing the Appliance112
Removing the Appliance Cover113
Installing the Expansion Storage Kit Components114
Replacing the Appliance Cover120
Connecting One S Series Storage Shelf to an Appliance121
Connecting the S Series Storage Shelves to the Appliance121
Connecting Two S Series Storage Shelves to an Appliance124
Connecting Three S Series Storage Shelves to an Appliance129
Connecting Four S Series Storage Shelves to an Appliance136
Connecting the Fifth S Series Storage Shelf to an Appliance144
Connecting the Sixth S Series Storage Shelf to an Appliance152
Connecting the D Series Storage Shelves to the Appliance160
Connecting One D Series Storage Shelf to an Appliance161
Connecting Two D Series Storage Shelves to an Appliance162
Connecting Three D Series Storage Shelves to an Appliance164
Connecting Four D Series Storage Shelves to an Appliance166
Connecting the Fifth D Series Storage Shelf to an Appliance168
Connecting the Sixth D Series Storage Shelf to an Appliance172
Appendix B Adding Storage Shelves to an Operating Appliance176
- That Has at Least One Storage Shelf Attached176
- Overview176
- Moving the MSDP Partition from a Base Disk to an Expansion Disk for Optimum Performance177
- Additional Storage Shelf Scenarios186
- Installing S Series Storage Shelves to an Appliance that Has at Least One Storage Shelf187
- Recabling to Connect Additional S Series Storage Shelves187
- Connecting Additional Shelves to an Appliance that Already Has One Operating Shelf189
- Connecting Additional Shelves to an Appliance that Already Has Two Operating Shelves192
- Connecting a Storage Shelf to an Appliance that Already Has Three Operating Shelves195
- Installing D Series Storage Shelves to an Appliance that Has at Least One Storage Shelf198
- Recabling to Connect Additional D Series Storage Shelves198
- Connecting Additional Shelves to an Appliance that Already Has One Operating Shelf200
- Connecting Additional Shelves to an Appliance that Already Has Two Operating Shelf202
- Connecting Additional Shelves to an Appliance that Already Has Three Operating Shelf204
Appendix C Configuring the Disk Space for New Netbackup Expansion Storage Shelves206
- Adding the Disk Space of Additional Storage Shelves from the Netbackup Appliance Shell Menu206
- Adding the Disk Space of Additional Storage Shelves from the Netbackup Appliance Web Console208
Appendix D Configuring the Disk Space for New Flex Expansion Storage Shelves210
- Adding the Disk Space of an Expansion Storage Shelf from the Flex Appliance Console210

Other manuals for VERITAS 5250

Product Description Guide78 pages

Hardware Service Procedure10 pages

Related product manuals

VERITAS NetBackup 5240

38 pages

VERITAS NetBackup 5230

VERITAS 5250 - Page 71

Table of Contents

Other manuals for VERITAS 5250

Related product manuals