What to do if Vertiv Liebert MTP 60kVA shows 'Over Load' warning?
If your Vertiv UPS displays an 'Over Load' warning in Line mode, it means the connected devices are using more power than the UPS can provide. You should reduce the amount of load and check the output load capacity and specification.
What to do if Vertiv Liebert MTP 60kVA UPS displays 'Over Load Fail' warning?
If you see an 'Over Load Fail' warning on your Vertiv UPS, it indicates that the load devices are demanding more power than the UPS can supply. As a result, the line mode will switch to bypass mode. Reduce the load and check the output load capacity and specification.
What should I do if my Vertiv UPS indicates 'Battery Open'?
If your Vertiv UPS is showing a 'Battery Open' warning, it means the battery is not connected. Here's what you should do: 1. Check the battery breaker. 2. Ensure the battery connection is secure. 3. Verify the nominal battery voltage setting. If the problem persists, contact service personnel.
What to do if Vertiv Liebert MTP 60kVA UPS shows 'EPO Active' warning?
If your Vertiv UPS shows an 'EPO Active' warning, check if the connector is loose when EPO acts abnormally.
What to do if my Vertiv Liebert MTP 60kVA displays 'Fault! Over Load Fault'?
If your Vertiv UPS shows 'Fault! Over Load Fault', this means a heavy overload is causing the UPS fault. You should reduce some of the load.
What to do if Vertiv Liebert MTP 60kVA displays 'Warning! Fan Lock'?
If your Vertiv UPS displays a 'Warning! Fan Lock', check if the fan is blocked or contact service personnel.
What to do if Vertiv Liebert MTP 60kVA UPS shows 'Fault! Inverter Soft Start Time Out'?
If your Vertiv UPS displays 'Fault! Inverter Soft Start Time Out', it means the inverter voltage cannot reach desired voltage within specified duration. Turn off the UPS and then restart it. If it fails again, contact service personnel.
What to do if Vertiv Liebert MTP 60kVA UPS shows 'Fault! Bus Soft Start Time Out'?
If your Vertiv UPS displays 'Fault! Bus Soft Start Time Out', it means the rectifiers could not start due to low DC bus voltage within specified duration. Turn off the UPS and then restart it. If it fails again, contact service personnel.
What does 'Fault! Bus Over Voltage' mean on Vertiv UPS?
If your Vertiv UPS displays 'Fault! Bus Over Voltage', it indicates that the DC bus voltage is too high. Contact service personnel.
What does 'Fault! Bus Under Voltage' mean on Vertiv Liebert MTP 60kVA?
If your Vertiv UPS displays 'Fault! Bus Under Voltage', it indicates that the DC bus voltage is too low. Contact service personnel.
General| Power Rating | 60 kVA |
|---|---|
| Capacity | 60 kW |
| Input Frequency | 50/60 Hz |
| Output Frequency | 50/60 Hz |
| Topology | Double Conversion Online |
| Operating Temperature | 0 to 40 °C |
| Cooling | Forced air |
| Battery Type | Valve Regulated Lead Acid (VRLA) |
| Relative Humidity | 0 to 95% non-condensing |
| Input Voltage | 380/400/415V AC, 3-phase, 4-wire + ground |
| Output Voltage | 380/400/415V AC, 3-phase, 4-wire + ground |
Installation procedures and requirements for the UPS.
Procedures and precautions for maintaining the UPS system.
Critical warnings for electrical connection safety.
Specifies the required environmental conditions for UPS installation.
Safe handling and movement procedures for the UPS cabinet.
Overview of the UPS unit's external components and features.
Description of the UPS control panel and its interface elements.
Guidelines and diagrams for UPS wiring and connections.
Detailed explanation of all UPS operating modes.
Procedures for operating the UPS, including startup and shutdown.
Overview of the different screens available on the UPS control panel.
Accessing and configuring UPS settings via the setup menu.
Comprehensive list of UPS fault and warning messages with explanations.
Details on UPS dry contact ports for external signaling.
Ports for PC communication and data transfer.
Step-by-step instructions for replacing the UPS power module.
Procedures for accessing and servicing internal UPS components.
Steps to safely transfer the UPS to maintenance bypass mode.
Compliance with European and international standards.
Physical dimensions, weight, and color of UPS models.
Detailed electrical specifications for UPS components.
Guidelines for input and output wiring in parallel systems.
Configuration of parallel boards and power modules for system setup.
Procedures for connecting parallel cables between UPS units.
Steps to safely power on a parallel UPS system.
Contact information and resources for technical support and service.
To Next Page