What to do if the charger is not functioning on my Victron energy MultiPlus Compact 12/1600/ 70-16?
If the charger on your Victron Energy Inverter is not functioning, it could be due to: * AC input voltage or frequency out of range: Ensure the input voltage is between 185 Vac and 265 Vac, and the frequency matches the setting. * Tripped thermal circuit breaker: Reset the 16 A thermal circuit breaker.
What to do if the alarm LED flashes on my Victron energy MultiPlus Compact 12/1600/ 70-16 Inverter?
If the alarm LED is flashing on your Victron Energy Inverter, it could be due to several reasons: * Low DC input voltage: Charge the battery or check the battery connections. * High ambient temperature: Place the inverter in a cooler, well-ventilated area or reduce the load. * Overload: Reduce the load on the inverter. * Excessive voltage ripple: Inspect the battery cables and terminals, and consider increasing the battery capacity if needed. * Intermittent low battery voltage and excessive load: Charge the batteries, decrease the load, use batteries with higher capacity, or use shorter/thicker battery cables.
Why is my Victron Energy Inverter battery not being charged fully?
If your Victron Energy Inverter's battery is not being charged fully, consider these possible causes and solutions: 1. Incorrect charging current: Set the charging current between 0.1 and 0.2 times the battery capacity. 2. Defective battery connection: Check the battery terminals for any issues. 3. Incorrect absorption voltage: Adjust the absorption voltage to the correct value. 4. Incorrect float voltage: Adjust the float voltage to the correct value.
What causes the battery to be overcharged in Victron Energy Inverter?
If the battery is overcharged in your Victron Energy Inverter, it could be due to: * Incorrect absorption voltage: Adjust the absorption voltage to the correct value. * Incorrect float voltage: Adjust the float voltage to the correct value. * Defective battery: Replace the battery. * Battery too small: Reduce the charging current or use a battery with a higher capacity. * Battery too hot: Connect a temperature sensor.
Why does the battery charge current drop to 0 when the absorption voltage is reached on Victron energy MultiPlus Compact 12/1600/ 70-16?
If the battery charge current drops to 0 when the absorption voltage is reached in your Victron Energy Inverter, it could be due to: * Battery overtemperature (> 50°C): Allow the battery to cool down, place it in a cool environment, and check for shorted cells. * Faulty battery temperature sensor: Unplug the battery temperature sensor from the MultiPlus, reset the MultiPlus by switching it off, waiting 4 seconds, and then switching it on again. If it now charges normally, the sensor is faulty and needs replacement.
General| Model | MultiPlus Compact 12/1600/70-16 |
|---|---|
| Input Voltage | 12 VDC |
| Input Voltage Range | 9.5 - 17 VDC |
| Output Power (Continuous) | 1600 VA |
| Continuous Output Power at 25°C | 1300 W |
| Output Power (Surge) | 3000 VA |
| Output Voltage | 230 VAC |
| Output Frequency | 50 Hz / 60 Hz |
| Efficiency | up to 93% |
| Charger Output | 70 A |
| Maximum AC Input Current | 16 A |
| Transfer Time | 20 ms |
| AC Input Voltage Range | 187-265 VAC |
| AC Input Frequency | 45 – 65 Hz |
| Protection | Overload, short circuit, over temperature |
| Operating Temperature | -40 to +65 °C |
| Humidity | 95% (non-condensing) |
Explanation of the adaptive 4-stage battery charging system.
Details on connecting battery cables, including cross-section and capacity.
Instructions for connecting AC input and output cables.
Requirements for parallel and three-phase operation setup.
Overview of default factory settings.
Detailed explanation of various configuration settings.
Common problems, causes, and solutions.
To Next Page