To Next PageTo Next PageWhy won't my ViewSonic PJD5153 Projector turn on?
If your ViewSonic Projector isn't turning on, first ensure the power cord is securely plugged into both the projector's AC inlet and a functioning power outlet. Check that the power outlet switch is on. Also, if the projector is cooling down, wait for the process to complete before attempting to turn it on again.
Why is my ViewSonic Projector remote not working?
If the remote control for your ViewSonic Projector isn't working, try these solutions: 1. Replace the battery with a new one. 2. Remove any obstacles between the remote and the projector. 3. Ensure you are within 8 meters (26 feet) of the projector.
What to do if my ViewSonic PJD5153 has no picture?
If you're not seeing a picture on your ViewSonic Projector, start by ensuring your video source is turned on and properly connected with the signal cable. Verify the projector is correctly connected to the input signal device. Finally, use the Source key on the projector or remote to select the correct input signal.
How to fix a blurred image on a ViewSonic PJD5153 Projector?
If your ViewSonic Projector image is blurred, try these steps: * Adjust the focus of the lens using the focus ring. * Adjust the projection angle, direction, and height of the projector to properly align it with the screen.
General| Matrix size | 0.55 \ |
|---|---|
| Matrix type | DMD |
| Native aspect ratio | 4:3 |
| Projection distance | 1 - 8 m |
| Projection technology | DLP |
| Contrast ratio (typical) | 2400:1 |
| Screen size compatibility | 30 - 300 \ |
| Projector native resolution | SVGA (800x600) |
| Keystone correction, vertical | -40 - 40 ° |
| Vertical synchronization (max) | 0.12 kHz |
| Vertical synchronization (min) | 0.023 kHz |
| Horizontal synchronization (max) | 102 kHz |
| Horizontal synchronization (min) | 15 kHz |
| Focus | Manual |
| Zoom capability | Yes |
| Focal length range | - mm |
| RS-232 ports | 1 |
| Maximum analog resolution | 1600 x 1200 pixels |
| Lamp power | 190 W |
| Lamps quantity | 1 lamp(s) |
| Light source type | Lamp |
| Service life of light source | 5000 h |
| 3D | - |
| Full HD | No |
| Supported video modes | 1080i, 1080p, 480i, 480p, 576i, 576p, 720p |
| Analog signal format system | NTSC, NTSC M, PAL 4.43, PAL 60, PAL B, PAL D, PAL G, PAL H, PAL I, PAL M, PAL N, SECAM, SECAM B, SECAM D, SECAM G, SECAM K, SECAM K1, SECAM L |
| Supported graphics resolutions | 1600 x 1200 (UXGA) |
| USB connector type | Mini-USB |
| HDMI ports quantity | 0 |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| VGA (D-Sub) ports quantity | 3 |
| Component video (YPbPr/YCbCr) in | 2 |
| Noise level | - dB |
| Certification | CB, TUV-GS, UL/cUL, FCC (including ICES-003), CE, C-Tick Mexico Energy test/Registration, EAC, UkrSEPRO/EMC DOC, UL COC, TUV-S Mark(Argentina), PSB, KCC, KC, SASO, CCC WEEE, RoHS, REACH, SVHC, ErP |
| RMS rated power | 2 W |
| Placement | Desktop |
| Product type | Standard throw projector |
| Product color | Black |
| Market positioning | Presentation |
| Power source | AC |
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 0.5 W |
| Power consumption (typical) | 265 W |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 10 - 90 % |
| Sustainability certificates | RoHS |
Weight and Dimensions| Depth | 228 mm |
|---|---|
| Width | 316 mm |
| Height | 103.7 mm |
| Weight | 2100 g |
Device complies with FCC Rules, operation subject to two conditions.
Detailed safety guidelines for projector operation and handling.
Safety advice for mounting the projector on a ceiling.
Describes the buttons and controls located on the projector unit itself.
Explains the function of each button on the remote control.
Instructions on how to set a password for projector security.
Configures password protection and panel lock.
How to enable economic mode to save power and extend lamp life.
Addresses issues when the projector fails to power on.
Solutions for when no image is displayed on the screen.
Troubleshooting steps for unfocused or misaligned images.
Details what is covered under the projector's warranty.
Details items and conditions not covered by the projector's warranty.
