To Next PageTo Next PageHow to fix ViewSonic Pro9000 Projector when no image appears on screen?
If your ViewSonic projector displays no image, ensure all cables and power connections are correctly and securely connected as described in the “Installation” section. Also, check that the connector pins are not crooked or broken, the projection lamp is securely installed, and the lens cap has been removed, and that the projector is switched on.
How to focus ViewSonic Pro9000 Projector?
If your ViewSonic projector image is out of focus, first, ensure that the lens cap is removed. Then, adjust the “Focus Ring” on the projector lens. Also, verify that the projection screen is within the required distance of 4.1-16.4 feet (1.3-5.0 meters) from the projector.
What to do if ViewSonic Projector image is too small or too large?
If the image on your ViewSonic projector is too small or too large, try moving the projector closer to or further from the screen. Alternatively, press “Menu” on the control panel, go to “SETTING” --> “Aspect Ratio” and try the different settings.
How to correct slanted sides on ViewSonic Pro9000 Projector image?
If your ViewSonic projector image has slanted sides, reposition the projector so that it is centered on the screen and below the bottom of the screen, if possible. You can also use “SETTING” --> “V Keystone” from the OSD to make an adjustment.
How to fix a reversed image on ViewSonic Pro9000?
If the image on your ViewSonic projector is reversed, adjust the “Projection” setting to correct it.
Why is my ViewSonic Projector image flickering?
If your ViewSonic projector image is unstable or flickering, try adjusting the “Phase” to correct it. You may also try changing the monitor color setting from your computer.
Why is the image stretched on my ViewSonic Pro9000 when playing DVDs?
If the image on your ViewSonic projector is stretched when displaying a 16:9 DVD title: * If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD. * If the image is still stretched, you will also need to setup the display format as 16:9 (wide) aspect ratio type on your DVD player.
What to do if ViewSonic Pro9000 Projector stops responding?
If your ViewSonic projector stops responding to all controls, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power.
How to fix partial image on ViewSonic Projector?
To correct a partial, scrolling, or incorrectly displayed image on your ViewSonic projector, press the “?” (left direction) button on the control panel, or the “Auto Sync” button on the remote control to auto synchronize for the analog PC signal.
How to remove vertical flickering bar on ViewSonic Pro9000?
If your ViewSonic projector image has a vertical flickering bar, use the “Frequency” setting to make an adjustment. Also, check and reconfigure the display mode of your graphic card to ensure it is compatible with the product.
General| Display Technology | DLP |
|---|---|
| Native Resolution | 1920 x 1080 |
| Throw Ratio | 1.5 - 1.8:1 |
| Zoom Ratio | 1.2x |
| Screen Size | 30 - 300 inches |
| Contrast Ratio | 100, 000:1 |
| Connectivity | HDMI, VGA, USB |
| Output Ports | Audio Out |
| 3D Support | Yes |
| Keystone Correction | Vertical ±40 degrees |
| Noise Level | 28 dB |
| Input Ports | HDMI, VGA, Composite |
Details FCC rules compliance for digital devices and interference.
Steps for connecting the projector to a computer or notebook for display.
Guides on connecting various video sources like DVD players and set-top boxes.
Procedure for safely powering on the projector and connecting sources.
Instructions for safely shutting down the projector and what to do afterward.
How to use the projector's feet to adjust the image height and angle.
Guide to rotating the focus ring for a clear and sharp projected image.
Information on optimizing screen size and distance for the best viewing experience.
Detailed explanation of the projector's physical control panel buttons and their functions.
Description of the projector's OSD menus for making adjustments and settings.
Step-by-step instructions for navigating and operating the OSD menus.
Adjustments for sharpness, saturation, tint, and volume in video input modes.
Settings for computer input, including frequency, phase, and position adjustments.
Correcting vertical image distortion to make it appear rectangular.
Guidance for diagnosing and resolving common projector issues.
Solutions for common issues like no image, scrolling, or incorrect display.
Lists supported computer and video resolutions and sync frequencies.
