16
Standby/Lock
Standby mode allows you to service your spa. Pumps can be
stopped for 30 minutes in this mode, and will automatically
restart after. Select Standby mode by pressing the pause/standby
icon. e home/status screen and normal spa function will resume
after the 30 minute standby period.
e Lock option allows the user to partially or completely lock
the keypad. To lock the keypad select “Lock Settings” and,
when asked, select a 4-digit code. e same code will be needed
to unlock the keypad. To lock the keypad again, you will be
prompted to select another 4-digit code.
e keypad can be unlocked with a universal unlock code (3732)
or by a reset of the keypad. When Full Lock is selected, all
functions are locked. In Partial Lock, you may activate accessories,
but spa settings may not be changed.
Network
is screen allows you to connect to a Wi-Fi network such as is
used with the Cloud Control 2 (in.touch2) module (optional).
When a CloudControl2 (in.touch 2) module is detected, this
network will appear. Please refer to the CloudControl 2 manual
for specific instructions on setting up your module and network.
Miscellaneous
In the Miscellaneous submenu you can change the Warm
weather* and Info messages options.
When pumps are running, they produce heat that may increase
your water temperature. “Warm Weather” option gives you the
option to bypass the pack filtration over temperature feature.
When Warm Weather is “OFF” the filtration over-temperature
is disabled and your spa filtering will continue even if the water
temperature is high.
* Depending on spa configuration
IMPORTANT: Please do not make changes in this section
unless you are a qualified electrician.
In this section you can change the low-level configuration, as
well as modify the number of phases and the input current
value.* Please refer to the diagram on the spa control center box,
located inside of the equipment compartment, for the default
configuration of your specific spa model. Once the modification is
completed, confirm selection when asked and touch the Settings
icon to return to the Settings menu.
NOTE: On initial connection the installer is prompted for
electrical configurations. e Low-Level setting is selected by the
installer. e Phase and Amperage is set automatically. Default
settings should be confirmed by the installer to match the actual
phase and amperage at the spa’s installation location. In rare
occasions it may be necessary to adjust the Phase and Amperage
setting to match the actual service available at the installation
location using the instructions above.
* Depending on the pack configuration, a code may be required to
modify the low-level number. is code is 5555.
About
is section displays technical information about the Premium
and Design Line (A1000) control software version and applicable
revisions of the different components of your system.
Audio System Controls (Optional)
Press the Audio icon to access “in.stream 2” player controls.
If you are using a device with Bluetooth technology, it must be
connected for functions to work.*
Speakers settings: Move the sliders to adjust the Balance, Fader
and Subwoofer settings. e Fader and Subwoofer sliders will
only appear in the Speakers menu if the corresponding speakers
are available.
Source menu: To change the audio source, simply tap on the
“Audio Settings” menu and select desired audio source or device.
Note that only the sources available on the Premium or Design
Line Audio will be displayed in the source menu.
Disconnect Bluetooth: If a device with Bluetooth technology
is connected to the Premium or Design Line Audio, you can
disconnect it by pressing the Disconnect button at the bottom
of the screen. Doing so will also prevent the audio system from
automatically reconnecting to this specific device until it has been
reconnected using the device itself.
e first time you use your Bluetooth device with a Premium
or Design Line Audio system you must first “pair” or connect
your device to the spa audio system according to the standard
functionality of your specific device.* Each device must be
connected separately.
* Use code 5555 to pair.
For proper function, place your Bluetooth device within 20 feet
(6 meters) of your spa. e device should have “line of sight” to
the spa control panel / equipment door area.
NOTE: Certain house construction materials and other
obstructions can impair Bluetooth connectivity. You may need to
experiment with where to place your device for best results.
To Next Page
Loading...
Need help?
General
