20
You can lock the keypad by selecting one of 3 security levels:
Unlock, Partial lock, or Full lock. e Partial level locks the set
point adjustment and many options in the settings menu. e
Full level locks all keypad functions. To unlock the keypad
(either Partial or Full), press and hold the top selection key (Key
4) for 5 seconds.
Miscellaneous
In the Miscellaneous submenu you can change the Warm
weather* and Info messages options.
You may select to bypass the spa filtration over-temperature
feature. When Warm weather is “Off ”, the filtration over
temperature feature is disabled. is allows the spa to continue
filtering even through the water temperature is high.
Configure the main window message center with the Info
messages submenu. When set to “Display, all information”
messages are displayed without exception. When set to “Hide”
some detailed messages are not displayed when they occur to keep
the message center simple.
* Depending on spa configuration
IMPORTANT: Please do not make changes in this section
unless you are a qualified electrician.
In this section you can change the low-level configuration, as
well as modify the number of phases and the input current
value.* Please refer to the diagram on the spa control center box,
located inside of the equipment compartment, for the default
configuration of your specific spa model.
Use the and buttons to move to the selection you want
to modify. Use Key 2 to select, and the and buttons to
move through the selections. Press Key 2 again to confirm. Please
see the techbook for your spa system for details on low-level
settings. Once you have changed the number of phases in the
menu you will be unable to use the and buttons to return
to the Low-level configuration menu. Please go back and access
the menu again. When you change to low-Level configuration
of the pack, all Comfort Line control settings will reset (same as
Factory reset feature).
NOTE: On initial connection the installer is prompted for
electrical configurations. e Low-Level setting is selected by the
installer. e Phase and Amperage is set automatically. Default
settings should be confirmed by the installer to match the actual
phase and amperage at the spa’s installation location. In rare
occasions it may be necessary to adjust the Phase and Amperage
setting to match the actual service available at the installation
location using the instructions above.
* Depending on pack configuration, a code may be required
to change the low level number, number of phases or input
current. is code is “5555”.
About
is screen displays technical information about the control
system (R800) software on your Comfort Line spa and applicable
revisions of the different components of your system.
Audio System Controls (Optional)
Press to access “in.stream 2” player controls.
If you are using a device with Bluetooth technology, it must be
connected for functions to work.*
*Use code 5555 to pair.
Note: Play/Pause functions apply only to Bluetooth source.
Change Track or station functions works with all sources except
AUX.
Turning power On/Off: Press the Power key to turn the
in.stream 2 on or off.
Selecting the source: Press the Source key to toggle between
available sources.
Play/Pause audio: Press the Play/Pause button to start or pause
the audio.
Adjusting the volume: Press the Volume Up or the Volume
Down key to increase or decrease the volume.
Changing tracks: Use the Last Track and Next Track keys to
change tracks. Note that in FM mode these functions can be
useed to change stations.
Disconnect: is option can be found under the Audio section
in the Settings menu.
Fader, Balance and Subwoofer: Fader, Balance and Subwoofer
settings can be edited under the Audio section in the Settings
menu if your in.stream 2 supports it.
e first time you use your Bluetooth device with the Comfort
Line Audio system you must first “pair” your device to the spa
audio system according to the standard pairing functionality of
your specific device. Each device must be paired separately.
For proper function, place your Bluetooth device within 20 feet
(6 meters) of your spa. e device should have “line of sight” to
the spa control panel / equipment door area.
NOTE: Certain house construction materials and other
obstructions can impair Bluetooth connectivity. You may need to
experiment with where to place your device for best results.
To Next Page
Loading...
Need help?
General
