19
When using the Settings menu or submenus the screen will
revert back to the spa mode and Home/Status screen if no key
is pressed for 60 seconds. Note that if an accessory is not present
in your spa configuration, its menu will not appear. Refer to
the following section to get details about the possible settings,
accessories, and their detailed functionalities.
Water Care
e Water Care submenu will help you set up your ideal filtration
and heating settings. Choose from Away from Home, Standard
- Beginner, Energy saving, Super energy saving, and Weekender,
depending on your needs and preferences.
Use the ( Jets 2/Key 2) button to select your setting. A check
mark will appear within the selected icon to confirm your selected
mode.
In the descriptions of each mode below “Economy mode” means
that the set point will be reduced by 7°C*, which means that the
heating system will not be engaged unless the temperature falls to
7°C below the spa’s set temperature.
e filtration schedule shown on the screen will apply to the main
filtration pump. If your spa uses a circulation pump configured to
run 24 hours, the screen will show you the purge setting instead
of filtration. e purges are pre-programmed for a fixed number
of minutes, therefore the duration will be set to N/A on the
screen, and only the start time can be modified.
Water Care Modes
Away: In Away mode the spa temperature set point will be
reduced by 7°C (see description of “Economy mode” above). Spa
will remain in Economy mode at all times of the day and all days
of the week.
Standard - Beginner: In Standard mode the spa will heat to the
set point and filter according to the spa’s standard configuration.
Spa will heat to set point at all times and all days of the week.
Energy Savings: In Energy Savings mode the spa temperature
set point will be reduced by 7°C (see description of “Economy
mode” above) during peak daytime hours. Spa will heat to normal
set point during evening hours and on the weekend.
Super Energy Savings: In Super Energy Savings mode the spa
temperature set point will be reduced by 7°C (see description of
“Economy mode” above) during peak daytime hours. Spa will heat
to normal set point during evening hours, every day of the week.
Weekender: In Weekender mode the spa temperature set point
will be reduced by 7°C (see description of “Economy mode”
above) from Monday to Friday. Spa will heat to set point at all
times on the weekend (Saturday & Sunday).
Default Settings: e Default Settings option will restore all
Water Care modes and schedules to the spa’s default settings. You
will be asked to confirm your choice.
Modifying Water Care Schedules
To modify a Water Care mode schedule, use the lighted key to
the right of the screen (Key 5) to open the selected Water
Care menu.
You can adjust schedules using the ( Jets 2/Key 2) button
to select each menu item. Press Key 2 again to cycle to each
submenu item.
You may add a schedule to a mode by selecting the mode’s
schedule list with Key 5 (middle), scrolling down to Add, and
then selecting this option with Key 2.
To delete a schedule, press Key 4 (top) when that schedule is
selected within a specific mode’s schedule list.
You have several possibilities for setting each schedule (Mon-Fri,
weekend, every day, or single days). e schedules will be
repeated every week. e time and duration are set in 30 minute
increments. Ensure that you have selected the desired Water Care
mode in the main Water Care menu. Once you have set your
customized schedule, use the ( Jets 1/Key 1) button to go back
to the Home/Status screen.
Set Date and Time of Day
Setting the correct date and time is important for settings to
function as expected. Upon restarting your spa adjust the time
format (24 hr. or AM/PM), change the year, date, and time as
needed.
Within the Settings menu use the and buttons and
then the ( Jets 2/Key 2) button to select the Date & Time
submenu.
Use the and buttons to choose the setting that
you wish to adjust, and select it by pressing Key 2. Use the
and buttons to change the parameters, and key 2
to move between options. ( Jets 1/Key 1) will take you back
to the main Settings menu.
Adjust Keypad Settings
In this Settings submenu you can change the temperature unit,
language, display orientation, and keypad security. Within the
Settings menu use the and buttons and then the
( Jets 2/Key 2) button to select the Keypad Settings submenu.
Use the and buttons to choose the setting that you wish
to adjust, and select it by pressing Key 2. Use the and
buttons to change the parameters, and key 2 to move between
options. (Jets 1/Key 1) will take you back to the main
Settings menu.
When you change the display orientation, the contextual options
and arrow keys adjust to the chosen orientation. e Mode
and Menu keys remain unchanged, as well as the accessory
keys in the main Spa menu.
To Next Page
Loading...
Need help?
General
