EasyManuals Logo

VIOMI V3 Max User Manual

VIOMI V3 Max
22 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #14 background imageLoading...
Page #14 background image
12
Four suction modes are available in the Mi Home/Xiaomi Home app:
Silent, Standard, Medium, and Turbo. The default mode is Standard.
Cleaning Preferences
In the Do Not Disturb mode, the vacuum-mop will not resume
cleanup, perform scheduled cleanup, or issue voice alerts.
Do Not Disturb Mode is enabled by default and can be disabled via
the app.
Do Not Disturb Mode
You can use the app to set up the zoned area, then the vacuum-mop
will clean up within the zoned area you selected.
Zoned Area
How to Use
When the vacuum-mop is on the charging dock, it will automatically
turn on and cannot be turned off.
To manually turn on the vacuum-mop, press and hold the buon until
the indicator lights up. When the vacuum-mop is in standby mode
and not on the charging dock, press and hold the buon to turn
it off.
Turning On/Off
Turn the vacuum-mop on, then press the buon . Depending on
the accessory installed, the vacuum-mop will automatically begin
vacuuming or mopping.
Cleaning
Turn the vacuum-mop on, then press the buon to send the
vacuum-mop to the dock to recharge.
When the vacuum-mop completes the cleaning task, it will automatical-
ly return to the dock for recharging, and the indicator is blinking yellow.
If the vacuum-mop starts running low baery during a cleaning
task, it will automatically return to the charging dock to recharge.
Once the vacuum-mop is fully charged, it will resume cleanup
where it le off.
If the vacuum-mop automatically shuts down due to low baery,
manually place it onto the charging dock, and make sure the
charging terminals have a good contact.
Recharging
While the vacuum-mop is running, press any buon to pause it, then
press the buon to resume cleaning. Pressing the buon
will end the current cleaning task and send the vacuum-mop back to
the charging dock.
Pausing
If the vacuum-mop encounters an error during operation, the
indicator will blink red and you will hear a voice alert. To check for a
solution, please refer to the Troubleshooting section.
If no action is taken within 5 minutes, the vacuum-mop will
automatically enter sleep mode.
Fault Status
The vacuum-mop will automatically enter sleep mode aer 5
minutes of inactivity. To wake it up, press any buon or use the app.
• The vacuum-mop will not enter sleep mode while on the charging
dock.
• The vacuum-mop will automatically turn off aer being in sleep
mode for 6 hours.
Sleep Mode
If you need to add more water to the vacuum-mop or clean the mop
during a cleaning task, press any buon to pause the vacuum-mop,
then remove the water tank. Aer adding water or cleaning the mop,
reinstall the water tank and mop, then press the buon to
resume the cleaning task.
Adding Water or Cleaning Mop During Cleaning

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the VIOMI V3 Max and is the answer not in the manual?

VIOMI V3 Max Specifications

V-RVCLM27A/V-RVCLM27B

Power IconPower
rated input voltage24 V
rated input current1.5 A
rated power35 W
Battery IconBattery
battery capacity5200 mAh
battery voltage14.4 V
output24 V 1.5 A
Wireless Connectivity IconWireless Connectivity
wireless connectivityWi-Fi IEEE 802.11b/g/n 2.4 GHz
operation frequency2400-2484 MHz
maximum output power≤18.5 dBm
Weight and Dimensions IconWeight and Dimensions
dimensionsφ350 × 105 mm
net weight3.6 kg

BLJ38W240150P-U

Power IconPower
rated output voltage24 V
rated output current1.5 A
input voltage range100–240 V~, 50/60 Hz, 1.0 A

Charging Dock

Weight and Dimensions IconWeight and Dimensions
dimensions197 × 143× 84 mm

Related product manuals