EasyManuals Logo

Vox Valvetronix ToneLab SE User Manual

Vox Valvetronix ToneLab SE
82 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #50 background imageLoading...
Page #50 background image
40
1. CLASSIC CHORUS (CL CHORUS) MONO IN/MONO OUT 1
(M
ODE=1,3) MONO IN/MONO OUT 3 (MODE=2)
This models a chorus unit that has two modes (chorus and vibrato), and is best-
known for being built into a guitar amp. There’s no parameter to switch between
chorus and vibrato, but you can use the SPEED and DEPTH knobs to create
either of these sounds, giving you an even broader range of possibilities than the
original unit! The output vibrato mode allows you to create vibrato (pitch modula-
tion) by outputting just the effect sound.
2. STEREO CHORUS (ST CHORUS) MONO IN/STEREO OUT 1
A stereo chorus in a yellow case. A sense of stereo is created by inverting the
phase of the effect sound for the right output, producing a feeling of spaciousness
that is somewhat different than the stereo effect of CLASSIC CHORUS.
3. CLASSIC FLANGER (CL FLANG) MONO IN/MONO OUT 1
A model of a truly classic analogue flanger that “unchained” a highly influential
modern guitarist who many hail as the “godfather of two handed tapping.
[1] “SPEED” 0.100–10.00 [Hz] * Adjusts the modulation speed.
[2] “DEPTH” 0.0–10.0 * Adjusts the modulation depth.
[4] “MANUAL 1.0–10.0 * Adjusts the center frequency of the sweep. If
DEPTH is set to 10, MANUAL will not function.
[5] “MODE” 1, 2, 3 Selects the output mode.
1: Mono output.
2: Stereo mode in which the effect is panned
right, and the dry sound panned left.
3: Vibrato mode, in which only the effect sound is
output. Setting MANUAL to 10 will minimize the
delay of the output sound.
[1] SPEED 0.100–10.00 [Hz] * Adjusts the modulation speed.
[2] DEPTH 0.0–10.0 * Adjusts the modulation depth.
[3] MANUAL 1.0–10.0 * Adjusts the center frequency of the sweep. If
DEPTH is set to 10, MANUAL will not function.
[6] MIX 0.0–10.0 * Adjusts the mix amount of the effect sound.
[1] “SPEED” 0.100–10.00 [Hz] * Adjusts the modulation speed.
[2] “DEPTH” 0.0–10.0 * Adjusts the modulation depth.
[3] “RESO” 0.0–10.0 * Adjusts the amount of resonance.
[4] “MANUAL 1.0–10.0 * Adjusts the center frequency of the sweep. If
DEPTH is set to 10, MANUAL will not function.
[5] “OFFSET” 0.0–10.0
Adjusts the starting position of the LFO. If you
assign “FLN TRIG” to a control pedal, the LFO will
be reset to the starting position specified by OFF-
SET whenever you operate the control pedal. When
you defeat BYPASS, the LFO will start from the posi-
tion you specify here. (p.56 Control pedal settings)

Table of Contents

Other manuals for Vox Valvetronix ToneLab SE

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Vox Valvetronix ToneLab SE and is the answer not in the manual?

Vox Valvetronix ToneLab SE Specifications

General IconGeneral
BrandVox
ModelValvetronix ToneLab SE
CategoryRecording Equipment
LanguageEnglish

Related product manuals