EasyManuals Logo

Vox Valvetronix ToneLab SE User Manual

Vox Valvetronix ToneLab SE
82 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #53 background imageLoading...
Page #53 background image
AMP TYPECABINET
TYPE
PEDAL
MODULATION
DELAYREVERB Amp/Effect
43
8. PITCH SHIFTER (PITCH) MONO IN/MONO OUT 1
This is a pitch shifter with a range of two octaves up or down, rivaling sophisticated
rack-mounted signal processors.
PITCH SHIFTER TIPS: If you assign the PITCH knob to an expression pedal,
you can use the pedal to control the pitch change. (
p.53
Using the expression
pedal to control the sound)
9. MOD DELAY (MOD DLY) M
ONO
I
N
/M
ONO
O
UT
1 (M
ODE
=1)
M
ONO
I
N
/M
ONO
O
UT
3 (M
ODE
=2) M
ONO
I
N
/S
TEREO
O
UT
1 (M
ODE
=3)
This models an analog delay that lets you add a vibrato effect to the delayed
sound. The actual unit provided 400 ms of delay time, but this simulation extends
this up to 1400 ms while maintaining the same warm sound, and can also be used
as a sub-delay for the DELAY section. The CHORUS/VIBRATO switch of the origi-
nal unit has been replaced by a knob with a range of 0.1–10 Hz, giving you even
more versatility than the original.
CONTROL pedal: ROT SPD: If you select “ROT SPD” as the CONTROL pedal
setting, the rotation speed will alternate between
SLOW/FAST (SPEED 1/SPEED 2) each time
you press the CONTROL pedal switch. This lets
you control the effect just as on an actual rotary
speaker. (p.56 Control pedal settings)
[1] “PITCH” –24–+24 * Adjusts the pitch in 100-cent units.
[2] “FINE” –50–+50 * Adjusts the pitch in one-cent units.
[4] “TRACKING” 10–150 [ms]
Adjusts the tracking of the pitch shifter (i.e., how
closely it will follow). Shorter settings are effective if
the PITCH setting is close to 0, and longer settings
are effective if the PITCH setting is close to +/–24.
While listening to the pitch-shifted sound, adjust
this so that you do not have difficulty playing.
[5] “DIRECT” 0.0–10.0 * Adjusts the level of the direct sound.
[6] “EFFECT” 0.0–10.0 * Adjusts the level of the effect sound.
[1] “SPEED” 0.100–10.00 [Hz] * Adjusts the modulation speed.
[2] “DEPTH” 0.0–10.0 * Adjusts the modulation depth.
[3] “FEEDBACK” 0.0–10.0 * Adjusts the amount of feedback.
[4] “TIME” 1.0–10.0 * Specifies the delay time.
[5] “MODE” 1,2,3 Selects the output method.
1: Mono output.
2: Stereo mode with effect sound from the
right and dry sound from the left.
3: Reverse-phase stereo mode with dry +
effect in the left side and dry - effect in the
right side.
[6] “MIX” 0.0–10.0 * Adjusts the mix amount of the effect sound.

Table of Contents

Other manuals for Vox Valvetronix ToneLab SE

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Vox Valvetronix ToneLab SE and is the answer not in the manual?

Vox Valvetronix ToneLab SE Specifications

General IconGeneral
BrandVox
ModelValvetronix ToneLab SE
CategoryRecording Equipment
LanguageEnglish

Related product manuals