14
15
• Connected - when successfully paired
and connected to a Bluetooth headset,
the Bluetooth LED becomes steady on.
NOTE: When there is an incoming
call, you hear a ringing tone on your
Bluetooth headset and the Bluetooth
LED will turn off. You can answer the
incoming call with your Bluetooth
headset.
• Bluetooth headset in use - when the
connected Bluetooth headset is in use,
the Bluetooth LED becomes steady on.
• No connection - the Bluetooth LED
turns off.
Remove paired Bluetooth headset
1. Press or on the handset.
2. Press and hold /FIND HS at the back
of the telephone base for 4 seconds.
The paired Bluetooth headset will be
removed.
• You can use your connected Bluetooth
headset to answer calls or end the call.
• If you fail to connect your Bluetooth
headset to the telephone, re-try the pairing
steps above.
• To pair another Bluetooth headset to the
telephone, perform the pairing steps
above and the current paired headset will
be replaced by the new Bluetooth headset.
• While on a call using your Bluetooth
headset, keep your headset closer to the
telephone base (within 15 feet) and make
sure that there are no physical obstacles
such as large furniture or thick wall in
between.
Redial list
Each handset stores the last
10 telephone numbers dialed. Entries are
shown in reverse chronological order.
When there are already
10 entries, the oldest entry is deleted to
make room for the new entry.
Review a redial list entry
1. Press REDIAL to enter the redial list.
2. Press , , or REDIAL repeatedly
to browse until the desired entry
displays.
• You hear a double beep when you reach
the beginning or end of the redial list.
Dial a redial list entry
1. Press REDIAL to enter the redial list.
2. Press , , or REDIAL repeatedly
to browse until the desired entry
displays.
3. Press or to dial.
-OR-
1. Press or to take the line.
2. Press REDIAL to enter the redial list.
3. Press , , or REDIAL repeatedly
to browse until the desired entry
displays.
4. Press SELECT to dial the displayed
number.
Delete a redial list entry
1. Press REDIAL to enter the redial list.
2. Press , , or REDIAL repeatedly
to browse until the desired entry
displays.
3. When the handset displays the number
you want to delete, press DELETE. You
hear a confirmation tone.
Multiple handset use
Intercom
Use the intercom feature for conversations
between two handsets.
1. Press INT on your handset when not in
use.
• If you have only one handset, your
handset displays INT needs 2 HS.
• If you have two handsets, your
handset displays Calling HS X.
• If you have three or more handsets,
your handset displays
Intercom to. Use the dialing keys
to enter a destination handset. Your
handset displays Calling HS X.
The destination handset rings and its
screen displays HS X is calling.
2. To answer the intercom call, press ,
, INT or any dialing key (0-9,
or
) on the destination
handset. Both handsets now display
Intercom.
3. To end the intercom call, press OFF
or place the handset back in the
telephone base or charger.
• To cancel the intercom call before it is
answered, press OFF or INT.
• Press OFF or MUTE on the destination
handset to temporarily silence the intercom
ringer.
• If the destination handset does not answer
the intercom call within 100 seconds, is on
a call or out of range, the originating
handset displays Unable to call and returns
to idle mode.
• If there is an incoming call while the
originating handset displays Calling HS X,
the intercom request will be stopped and
the screen displays Incoming call.
• You can use four handsets on two pairs of
intercom calls. For example, when four
handsets are used on two pairs of intercom
calls, use the fifth handset for an outside
call.
Answer an incoming call during an
intercom call
When you receive an outside call during
an intercom call, there is an alert tone.
• To answer the outside call, press .
The intercom call ends automatically.
• To end the intercom call without
answering the outside call, press OFF.
The telephone continues to ring.
Call transfer using intercom
Use the intercom feature to transfer an
outside call to another system handset.
1. During a call, press INT.
• If you have two handsets, the
outside call is put on hold and your
handset displays Calling HS X.
• If you have three or more handsets,
your handset displays Intercom
to. Use the dialing keys to enter a
handset number. The outside call
is put on hold and your handset
displays Calling HS X.
The destination handset rings and its
screen displays HS X is calling.
2. To answer the intercom call on the
destination handset, press , , INT or
any dialing key (0-9,
,
or ). The
outside call is still on hold and both
handsets now display Intercom. You can
now have a private conversation with the
destination handset.
The Bluetooth® word mark and logos are owned
by Bluetooth SIG, Inc. and any use of such marks
by Advanced American Telephones and its parent,
VTech Holdings Limited, is under license. VTech
Holdings Limited is a member of Bluetooth SIG, Inc.
Other trademarks and trade names are those of their
respective owners.
To Next Page
Loading...
