24
25
Screen messages
Calling HS X
(for models with two
or more
handsets only)
You are calling another
handset (for intercom
calls).
Ended
You have just ended
a call.
HS X is
calling
(for models with two
or more handsets
only)
Another handset is
calling (for intercom
calls).
Incoming
call
There is an incoming
call.
INT needs 2
HS
Two handsets are
required for an
intercom call.
Intercom
The handset is on an
intercom call.
Intercom to
(for models with
three or more
handsets only)
You have started the
intercom process or
started transferring a
call, and need to enter
the desired handset
number.
Line in use
A system handset or
another telephone on
the same line is
in use.
List empty
There are no directory
entries.
Low battery
The battery needs to
be recharged.
Microphone
on
MUTE is turned off
and the person on the
other end can hear
you.
Muted
You have turned
off the handset
microphone. The other
party cannot hear you
but you can hear the
other party.
New
voicemail
There are new
voicemail message(s)
from your telephone
service provider.
No battery
You place the handset
in the telephone base
or charger without
installing a battery in it.
No line
There is no telephone
line connected.
Not
available
Another handset
is already in the
directory or caller ID
log.
Number
repeated
The telephone number
you have entered is
already stored in the
directory.
Out of range
or no pwr at
base
The telephone base
has lost power, or
the handset is out of
range.
Phone
The handset is on a
call.
Put in
charger
The battery is very
low. Put the handset in
the telephone base or
charger for recharging.
Quiet mode
off
The quiet mode is
turned off.
Quiet mode
on
The quiet mode is
turned on.
Rec mem full
The directory is full.
You cannot save any
new entry unless you
delete some current
entries.
Reg. failed
The handset
registration is not
successful.
Registering...
The handset
registration is in
progress.
Ringer muted
The handset ringer
is muted temporarily
during an incoming
call.
Speaker
The handset
speakerphone is in
use.
To register
HS...
...see manual
Screen display on
a non-registered
handset.
Unable to
call
The handset is out of
range while on a call.
Failed phone call (the
telephone line is in
use).
Failed intercom call
(there are already two
handsets being used).
XX missed
calls
There are new calls in
the caller ID log.
** Paging **
All system handsets are
being paged.
Frequently asked questions
Below are the questions most frequently
asked about the cordless telephone.
If you cannot find the answer to your
question, visit our website at
www.vtechphones.com or call
1 (800) 595-9511 for customer service. In
Canada, visit
phones.vtechcanada.com or call
1 (800) 267-7377.
My telephone
does not work
at all.
Make sure the telephone
base is installed properly,
and battery is installed
and charged correctly.
For optimum daily
performance, return the
handset to the telephone
base after use.
The display
shows No line. I
cannot hear the
dial tone.
Disconnect the telephone
line cord from your
telephone and connect
it to another telephone.
If there is no dial tone
on that other telephone
either, then the telephone
line cord may be
defective. Try installing a
new telephone line cord.
If changing telephone
line cord does not help,
the wall jack (or the wiring
to this wall jack) may
be defective. Contact
your telephone service
provider.
You may be using a new
cable or VoIP service, the
existing telephone jacks in
your home may no longer
work. Contact your service
provider for solutions.
To Next Page
Loading...
