WAGO 750 - Copyright

To Next Page

To Previous Page

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-471 4AI U/I Diff Galv

Manual

Version 1.0.0

1.3 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Main Page

Table of Contents3
Notes about this Documentation5
Validity of this Documentation5
Copyrights5
Copyright7
Symbols8
Number Notation10
Font Conventions10
Table 1: Number Notation10
Table 2: Font Conventions10
Important Notes11
Legal Bases11
Subject to Changes11
Personnel Qualifications11
Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying Provisions11
Technical Condition of Specified Devices12
Disposal12
Safety Advice (Precautions)13
Device Description15
Table 3: Compatibility List 750-47116
View18
Figure 1: View18
Table 4: Legend for Figure "View18
Connectors19
Data Contacts/Local Bus19
Figure 2: Data Contacts19
Power Jumper Contacts/Field Supply20
Figure 3: Power Jumper Contacts20
Table 5: Legend for Figure "Power Jumper Contacts20
Cage Clamp22
Figure 4: CAGE CLAMP ® Connectors22
Table 6: Legend for Figure "CAGE CLAMP ® Connectors22
Display Elements23
Figure 5: Display Elements23
Table 7: Legend for Figure "Display Elements23
Schematic Diagram25
Figure 6: Schematic Diagram25
Figure 7: Circuit Diagram25
Technical Data26
Device Data26
Supply26
Isolation26
Communication26
Table 8: Technical Data - Device26
Table 9: Technical Data - Supply26
Table 10: Technical Data - Isolation26
Table 11: Technical Data - Communication26
Inputs27
Connection Type27
Table 12: Technical Data - Inputs27
Table 13: Technical Data - Field Wiring27
Table 14: Technical Data - Power Jumper Contacts27
Table 15: Technical Data - Data Contacts27
Climatic Environmental Conditions28
Table 16: Technical Data - Climatic Environmental Conditions28
Approvals29
Standards and Guidelines30
Process Image31
Overview31
Table 17: Process Image - I/O Module750-47132
Status Bytes33
Table 18: Status Byte CH1_S033
Process Data34
Overview of Sensor Types34
Table 19: Process Data, Signal Types34
Table 20: Signal Types "035
Table 21: Signal Types "036
Signal Types "± 10 V", "± 200 MV" "± 20 Ma", Two's Complement (Default)37
Table 22: Signal Types "± 10 V", "± 200 MV", "± 20 Ma", Two's Complement37
Table 23: Signal Types "± 10 V", "± 200 MV" "± 20 Ma", Two's Complement with38
Table 24: Signal Types "± 10 V", "± 200 MV" "± 20 Ma", Amount/Sign Format38
Table 25: Signal Types "± 10 V", "± 200 MV" "± 20 Ma", Amount/Sign Format with39
Signal Type "Namur NE4340
Table 26: Signal Type "Namur NE43", Two's Complement40
Table 27: Signal Type "Namur NE43", Two's Complement with Status Information41
Table 28: Signal Type "Namur NE43", Amount/Sign Format42
Table 29: Signal Type "Namur NE43", Amount/Sign Format with Status43
Mounting44
Mounting Sequence44
Inserting and Removing Devices45
Inserting the I/O Module45
Figure 8: Insert I/O Module (Example)45
Figure 9: Snap the I/O Module into Place (Example)45
Removing the I/O Module46
Figure 10: Removing the I/O Module (Example)46
Connect Devices47
Connecting a Conductor to the CAGE CLAMP47
Figure 11: Connecting a Conductor to a CAGE CLAMP47
Connection Examples48
Figure 12: Connection Example 750-47148
Commissioning49
Parameterization with WAGO-I/O-CHECK49
Figure 13: WAGO-I/O-CHECK User Interface50
Parameterization Dialog51
Figure 14: Parameterization Dialog 750-47151
Toolbar on the Configuration Dialog52
Figure 15: Toolbar52
Table 30: Toolbar52
Navigation Area53
Figure 16: Navigation53
Table 31: Navigation53
Common54
Figure 17: Parameter „Common54
Table 32: "General" Parameters54
Channel Settings56
Figure 18: Parameter „Channel56
Table 33: Parameter „Channel56
Scaling58
Figure 19: Parameter "Scaling58
Table 34: "Scaling" Parameters58
Calibration60
Figure 20: "Calibration" Parameters61
Table 35: Calibration Parameters61
Figure 21: Offset Correction62
Figure 22: Gain Correction62
Scaling Measured Values64
Table 36: Variable Legend - Scaling Measured Values64
Diagnostics65
I/O Module Behavior in the Event of an Error65
Table 37: Priority Levels of Diagnostic Functions65
Table 38: Behavior in the Event of an I/O Module Error Dependent on the66
Firmware Changes68
Use in Hazardous Environments69
Marking Configuration Examples70
Marking for Europe According to ATEX and Iecex70
Figure 23: Marking Example According to ATEX and Iecex70
Figure 24: Text Detail - Marking Example According to ATEX and Iecex70
Table 39: Description of Marking Example According to ATEX and Iecex71
Figure 25: Marking Example for Approved Ex I I/O Module According to ATEX72
Figure 26: Text Detail - Marking Example for Approved Ex I I/O Module72
Marking for America (NEC) and Canada (CEC)73
Table 40: Description of Marking Example for Approved Ex I I/O Module According to ATEX and Iecex73
Table 42: Description of Marking Example for Approved Ex I I/O Module73
Figure 27: Marking Example According to NEC74
Figure 28: Text Detail - Marking Example According to NEC 50074
Table 41: Description of Marking Example According to NEC 50074
Figure 29: Text Detail - Marking Example for Approved Ex I I/O Module75
Figure 30: Text Detail - Marking Example for Approved Ex I I/O Module75
Table 43: Description of Marking Example for Approved Ex I I/O Modules75
Figure 31: Text Detail - Marking Example for Approved Ex I I/O Modules76
Table 44: Description of Marking Example for Approved Ex I I/O Modules76
Installation Regulations77
Special Notes Regarding Explosion Protection77
Special Notes Regarding ANSI/ISA Ex79
Appendix80
Configuration and Parameterization Using a GSD File with PROFIBUS DP and PROFINET IO80
4AI U/I Diff/Galv Configuration80
PROFIBUS DP Fieldbus Couplers/Controllers 750-333(/0Xx-000)80
750-833(/0Xx-000)80
PROFINET IO Fieldbus Couplers 750-375(/025-000), 750-377(/025-000)80
Table 45: PROFIBUS DP Configuration80
Table 46: Configuration 750-375(/025-000) und 750-377(/025-000)80
4AI U/I Diff/Galv Parameterization81
Figure 32: Example of the PROFIBUS DP Fieldbus Couplers/Controllers81
Figure 33: Example of the Fieldbus Couplers/Controllers Parameterization Dialog82
All PROFIBUS DP and PROFINET IO Fieldbus Couplers/Controllers83
Table 47: Specific Module/Channel Parameters for 75X-461/003-00083
PROFIBUS DP Fieldbus Couplers/Controllers 750-333(/0Xx-000), 750-833(/0Xx-000)84
PROFINET IO Fieldbus Couplers 750-375(/025-000), 750-377(/025-000)84
Table 48: General Module/Channel Parameters84
Table 49: General Module/Channel Parameters84
List of Figures87
List of Tables88

WAGO 750 - Copyright

Table of Contents

Related product manuals