EasyManua.ls Logo

Wayne-Dalton Quantum 3316 - User Manual

Wayne-Dalton Quantum 3316
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
TM
OWNER INSTALLATION AND
USER MANUAL Series 3000
Models 3214, 3314, 3316 & 3414
Automatic Garage Door Opener
For Sectional Overhead Residential Doors Only
DO NOT USE ON ONE PIECE DOORS
CONTENTS
Important Installation Instructions 2 Wireless Keyless Entry Installation 21
Features 4 Opening & Closing Force Adjustment
21
Door Tests 5 Contact Obstruction Sensing Adjustment
.
22
Pre-Assembly Check 5 Mechanical lock Adjustment 22
Installation Instructions 6 Operational Safety Rules 23
Installing Wall Station 8 Operation of Your Opener 24
Install Infrared Safety Sensors 10 Emergency Release Disconnect 26
Maintenance Schedule 27 Wall Station Code Change
and Programming
14
Trouble Shooting 28
Infrared Safety Sensors Alignment 15 Parts Breakdown-Rail Assembly 29
Transmitter Code Change & Programming 16 Parts Breakdown-Power Head Assembly
And Accessories
30
Travel Adjustment 19 Accessories 31
Obstruction Sensing Test 19 Warranty 32
Infrared Safety Sensor Obstruction Test 20 Customer Service Number 32
Copyright 2003 Wayne-Dalton Corp. Part No: 307545 Rev 3 12/3/2003
DOOR AND OPENER WILL NOT OPERATE PROPERLY UNTIL INFRARED SAFETY
SENSORS ARE INSTALLED AND PROPERLY ADJUSTED! DO NOT OPERATE DOOR
OPENER UNTIL FULLY INSTALLED, ADJUSTED & INSTRUCTED TO DO SO!
READ THE ENCLOSED INSTRUCTIONS CAREFULLY BEFORE
INSTALLING/OPERATING THIS OPENER! PAY CLOSE ATTENTION TO ALL
WARNING LABELS AND NOTES. THIS MANAUL SHOULD BE ATTACHED IN
CLOSE PROXIMITY TO THE G
A
RAGE DOOR OPENER.

Table of Contents

Questions and Answers

  • M
    Mr. Richard LynnAug 22, 2025
    What to do if my Wayne-Dalton Garage Door Opener closes and then returns to fully open position?
    • A
      Allison WongAug 22, 2025
      If your Wayne-Dalton Garage Door Opener closes and then immediately returns to the fully open position, and the opener light flashes, it could be due to a few reasons. First, check the door arm adjustment; adjust the rod in the tube to allow for about 1 inch of 'cushion' compression when the door is fully closed. Second, the close travel adjustment might be set beyond the normal door position; adjust the close travel with a screwdriver, turning it clockwise. Finally, inspect the floor for any obstructions like stones or ice and remove them.
  • M
    moorejustinSep 4, 2025
    What to do if Wayne-Dalton Quantum 3316 reverses before closing?
    • L
      Laura SanchezSep 4, 2025
      If your Wayne-Dalton Garage Door Opener reverses travel before reaching the fully closed position and the opener light flashes, it indicates the activation of the obstruction sensing system. Check for any binding in the door travel, such as the door 'stopping' or issues with the door tracks. Also, remove any loose or hanging objects on the door that might be activating the Infrared Safety Sensor. Finally, ensure that closing force is properly adjusted.
  • G
    Glenn FitzgeraldSep 2, 2025
    How to fix a Wayne-Dalton Quantum 3316 that won't work?
    • K
      Kelly GoodmanSep 2, 2025
      If your Wayne-Dalton Garage Door Opener won’t work from the wall button or radio control, there could be a few reasons. First, check the power to the opener, wall switch, and circuit breaker. Second, there might be a short circuit in the wires to the opener or wall button, so isolate by disconnecting the wires at the opener from the wall station. Finally, the motor protector may have tripped open due to excessive use, so allow the motor to cool for 20 minutes and try again.
  • B
    brian73Sep 1, 2025
    Why does my Wayne-Dalton Quantum 3316 Garage Door Opener close and then reopen?
    • J
      Jennifer HuertaSep 1, 2025
      If your Wayne-Dalton Garage Door Opener closes and then returns to the fully open position and the opener light flashes, it could be due to a few reasons. First, the door arm adjustment might be off. Adjust the rod in the tube to provide 1” of “cushion” compression when the door is fully closed. Second, the close travel adjustment may be set beyond the normal door position, so adjust the close travel with a screwdriver. Finally, check for any obstructions like stones or ice under the door and remove them.
  • M
    Mark McleanAug 30, 2025
    How to fix Wayne-Dalton Garage Door Opener when door does not open fully?
    • J
      Joshua StoneAug 31, 2025
      If your Wayne-Dalton Garage Door Opener door does not open fully and the light does not flash, it's likely that the open limit hasn't been set properly. To fix this, adjust the open travel with a screwdriver, turning it counter-clockwise to the desired setting. Remember that 1/4 turn equals 1 inch of travel.
  • K
    Kari BellAug 29, 2025
    How to fix Wayne-Dalton Garage Door Opener when door stops and does not close fully?
    • R
      Robert ClarkAug 29, 2025
      If your Wayne-Dalton Garage Door Opener door stops and doesn't close fully, it's possible that the close limit hasn't been set correctly. To resolve this, adjust the close travel with a screwdriver, turning it clockwise to achieve the desired setting. Note that a 1/4 turn equals 1 inch of travel.
  • K
    Kayla LambertAug 28, 2025
    Why Wayne-Dalton Quantum 3316 Garage Door Opener works from wall button but not remote?
    • M
      Molly BeardAug 28, 2025
      If your Wayne-Dalton Garage Door Opener works from the wall button but not from the radio control, the radio control system may not be working correctly. You can try the following: * Replace the battery in the transmitter if it's weak or dead. * Ensure the Security Code matches between the receiver and transmitter. * If multiple transmitters aren’t working, have the Motor Control Board tested.
  • M
    Michael Wilkerson MDAug 27, 2025
    What to do if my Wayne-Dalton Quantum 3316 Garage Door Opener door does not open and opener light flashes?
    • G
      Gilbert GrahamAug 27, 2025
      If your Wayne-Dalton Garage Door Opener door does not open and the opener light flashes, it could be due to a few reasons. First, there might be something obstructing the door's path, so disconnect the door from the operator and manually operate the door to find any obstructions. Alternatively, call a service person. Second, the opening force might be insufficient, so you may need to adjust it. Finally, a build-up of ice and snow around the door could be the problem, so shovel and clear the area.
  • H
    hfletcherAug 25, 2025
    Why does my Wayne-Dalton Garage Door Opener reverse before closing?
    • S
      Sarah GeorgeAug 26, 2025
      If your Wayne-Dalton Garage Door Opener reverses direction before fully closing and the opener light flashes, it indicates that the obstruction sensing system has been activated. This could be due to a few reasons. First, check for any binding in the door's movement, such as issues with the door stopping or the tracks. Second, remove any loose or hanging objects that might be activating the Infrared Safety Sensor. Lastly, the closing force might be insufficient, so you should adjust it.
  • C
    Christopher FrazierAug 23, 2025
    Why my Wayne-Dalton Quantum 3316 won’t work from wall button or radio control?
    • J
      Jacob AustinAug 23, 2025
      If your Wayne-Dalton Garage Door Opener doesn't work when you use the wall button or the radio control, the issue might stem from a few causes. First, there might be no power reaching the opener, so check the cord, outlet, wall switch, and circuit breaker. Second, a short circuit in the wires connecting to the opener or wall button could be the culprit; you can isolate this by disconnecting the wires at the opener from the wall station. Lastly, the Motor Protector might have tripped due to excessive use; allow the motor to cool down for about 20 minutes before trying again.

Summary

CONTENTS

Important Installation Safety Instructions

Crucial safety rules for safe installation and operation of the garage door opener.

Opener Features and Initial Testing

Overview of opener features and essential door balance tests before installation.

Core Installation Procedures

Step-by-step guide for mounting the opener, rail, and wall bracket.

Sensor and Control System Installation

Installing safety sensors (wired/wireless) and wall station components.

Programming Wireless Controls and Alignment

Setting security codes, programming controls, and aligning safety sensors.

Door Travel and Obstruction Adjustments

Adjusting door limits, closing force, and obstruction sensing features.

Opener Operation, Maintenance, and Troubleshooting

Guidance on using the opener, emergency release, routine maintenance, and solving common problems.

Parts, Accessories, and Warranty Information

Identification of parts, accessories, and details on product warranty and support.

Wayne-Dalton Quantum 3316 Specifications

General IconGeneral
Horsepower1/2 HP
Drive TypeChain Drive
Voltage120V
Frequency60 Hz
Remote ControlYes
Safety SensorsYes
Remote Controls Included2
SecurityRolling Code Technology
Battery BackupNo
Warranty1-Year Parts Warranty
Motor TypeAC Motor

Related product manuals