WEG W21 - EU Declaration of Conformity

Electric motors for explosive atmospheres | 3
Manufacturers:
WEG Equipamentos Elétricos S.A.
Av. Prefeito Waldemar Grubba, 3000
89256-900 - Jaraguá do Sul – SC – Brazil
www.weg.net
WEGeuro – Indústria Eléctrica S.A.
Headquarters:
Rua Eng. Frederico Ulrich,
Zona Industrial da Maia Sector V
4470-605 – Maia – Portugal
www.weg.net/pt
Contact person: Luís Filipe Oliveira Silva Castro Araújo
Authorised Representative in the European Union
(Single Contact Point)
Branch – Santo Tirso:
Rua António Joaquim Campos Monteiro, 510
Santa Cristina do Couto
4780-165 – Santo Tirso – Portugal
www.weg.net/pt
WEG (Nantong) Electric Motor Manufacturing CO., LTD.
No. 128# - Xinkai South Road, Nantong
Economic & Technical Development
Zone, Nantong, Jiangsu Province – China
www.weg.net/cn
WEG (Jiangsu) Electric Equipment CO., LTD.
No. 88, Huimin West Road, Chengbei Street,
Rugao City, Jiangsu Province – China
www.weg.net/cn
WEG Linhares Equipamentos Elétricos S.A.
Rod. BR 101, Km 161,5, s/n
Distrito Industrial Rio Quartel
Bairro Rio Quartel de Baixo
29915-500 – Linhares – ES – Brazil
ww.weg.net
Declares under sole responsibility that WEG electric motors and components used for following motor lines:
W21, W22X…, W50X…, W51HDX..., W60X… and HGF
when installed, maintained and used in applications for which they were designed, and in compliance with the relevant installation standards and
manufacturer’s instructions, comply with the provisions of the following relevant European Union harmonisation legislation, wherever applicable:
ATEX Directive 2014/34/EU;
RoHS Directive 2011/65/EU and its amendments (including Directive 2015/863/EU);
Regulation (EU) No 2019/1871 (as amended by Commission Regulation (EU) 2021/341)** and Directive 2009/125/EC**;
Machinery Directive 2006/42/EC
EMC Directive 2014/30/EU (electric motors are considered inherently benign in terms of electromagnetic compatibility).
The fulfilment of the safety objectives of the relevant European Union harmonization legislation has been demonstrated by compliance with the
following standards, wherever applicable:
EN IEC 60079-0:2018* / EN 60079-1:2014* / EN IEC 60079-7:2015 + A1:2018* / EN 60079 31:2014, EN 60204-1:2018 / EN 60204-11:2019 / EN
IEC 63000:2018, / EN 60034-2-1:2014, EN 60034-30-1:2014 and IEC TS 60034-25:2014
* A comparison of the current version of the EN IEC 60079-0:2018, EN 60079-1:2014 and EN IEC 60079-7:2015 + A1:2018 standards with the
previous versions used by some Baseefa and CESI ATEX certificates shows that there are no changes in the “state of the art” applicable to the
product covered by this Declaration of Conformity. The manufacturer hereby declares that the ATEX Certificates issued by Baseefa and CESI meet the
Essential Health and Safety Requirements of ATEX Directive 2014/34/EU.
Declaration of Incorporation
The products above cannot be put into service until the machinery into which they have been incorporated has been declared in conformity with the
Machinery Directive.
A Technical Documentation for the products above is compiled in accordance with part B of annex VII of Machinery Directive 2006/42/EC and the
following essential requirements of this directive are applied an fulfilled: 1.1, 1.2, 1.3.1, 1.3.2, 1.3.3, 1.3.4, 1.3.5. 1.3.6, 1.4.1, 1.4.2, 1.4.3, 1.5.1, 1.5.2, 1.5.3,
1.5.4, 1.5.5,1.5.6, 1.5.7, 1.6.1, 1.6.2, 1.6.3, 1.6.4, 1.7.1, 1.7.2, 1.7.3 and 1.7.4.
We undertake to transmit, in response to a reasoned request by the national authorities, relevant information on the partly completed machinery
identified above through WEG authorised representative established in the European Union. The method of transmission shall be electronic or physical
method and shall be without prejudice to the intellectual property rights of the manufacturer
The Quality System for the certificates described above is approved by SGS Fimko Oy (NB0598) under the Quality Assurance Notification SGS ATEX
5886 (WEG Equipamentos Elétricos S.A. and SGS ATEX 3862 (WEGeuro – Indústria Eléctrica S.A.).
The equipment marking, name and number of the Notified Body which performed the EU-type examination and the EU-type examination certificate
number issued are listed in chapter Certificates.
Signed for and on behalf of the manufacturer:
Carlos Lourenço
Product Compliance Supervisor
Jaraguá do Sul
August 23, 2022
Rodrigo Fumo
Engineering Director
Jaraguá do Sul
August 23, 2022
EU Declaration of Conformity