4 | Electric motors for explosive atmospheres
declares under sole responsibility that WEG electric motors and components used for following motor lines:
W21, W22X…, W50X…, W51HDX…, W60X… and HGF
when installed, maintained and used in applications for which they were designed, and in compliance with the relevant installation standards and manufacturer’s
instructions, comply with the provisions of the following relevant UK statutory requirements, wherever applicable:
The Equipment and Protective Systems Intended for use in Potentially Explosive Atmospheres
Regulations S.I 2016/1107 amended by S.I. 2019/696)
The Ecodesign for Energy-Related Products and Energy Information S.I. 2021/745
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic S.I. 2012/3032
Equipment
The Supply of Machinery (Safety) S.I. 2008/1597 amended by S.I.2011/2157
Electromagnetic Compatibility (electric motors are considered inherently benign in terms of electromagnetic S.I. 2016/1091
compatibility).
The fulfilment of the safety objectives of the relevant UK statutory requirements has been demonstrated by compliance with the following designated standards, wherever
applicable:
EN IEC 60079-0:2018 / EN 60079-1:2014 / EN IEC 60079-7:2015 + A1:2018 / EN 60079 31:2014 / EN 60204-1:2018
EN 60204-11:2019 / EN IEC 63000:2018 / EN 60034-2-1:2014 / EN 60034-30-1:2014 and IEC TS 60034-25:2014
Declaration of Incorporation (for motors above 1000V)
The products above cannot be put into service until the machinery into which they have been incorporated has been declared in conformity with the Supply of Machinery
(Safety) Regulation 2008.
A Technical Documentation for the products above is compiled in accordance with part B, Annex VII (Part 7 of Schedule 2) of Supply of Machinery (Safety) Regulations
2008, S.I. 2008/1597 and the following essential requirements of this statutory instrument are applied and fulfilled: 1.1, 1.2, 1.3.1, 1.3.2, 1.3.3, 1.3.4, 1.3.5. 1.3.6, 1.4.1,
1.4.2, 1.4.3, 1.5.1, 1.5.2, 1.5.3, 1.5.4, 1.5.5,1.5.6, 1.5.7, 1.6.1, 1.6.2, 1.6.3, 1.6.4, 1.7.1, 1.7.2, 1.7.3 and 1.7.4.
We undertake to transmit, in response to a reasoned request by the national authorities, relevant information on the partly
completed machinery identified above through WEG authorised representative established in the United Kingdom. The method of
transmission shall be electronic or physical method and shall be without prejudice to the intellectual property rights of the
manufacturer.
The Quality System for the certificates described above is approved by SGS Baseefa (AB1180) under the Quality Assurance Notification SGS UKEX 5886 (WEG
Equipamentos Elétricos S.A.) and SGS UKEX 3862 (WEGeuro – Indústria Eléctrica S.A.). The equipment marking, name and number of the Notified Body which
performed the UK-type examination and the UK-type examination certificate number issued are listed in chapter Certificates.
Manufacturers:
WEG EQUIPAMENTOS ELÉTRICOS S.A.
Av. Prefeito Waldemar Grubba, 3000
89256-900 - Jaraguá do Sul – SC – Brazil
www.weg.net
WEGEURO – INDUSTRIA ELECTRICA S.A.
Headquarters:
Rua Eng. Frederico Ulrich,
Zona Industrial da Maia Sector V
4470-605 – Maia – Portugal
www.weg.net/pt
Branch – Santo Tirso:
Rua António Joaquim Campos Monteiro, 510
Santa Cristina do Couto
4780-165 – Santo Tirso – Portugal
www.weg.net/pt
WEG (Nantong) Electric Motor Manufacturing CO., LTD.
No. 128# - Xinkai South Road, Nantong
Economic & Technical Development
Zone, Nantong, Jiangsu Province – China
www.weg.net/cn
WEG (Jiangsu) Electric Equipment CO., LTD.
No. 88, Huimin West Road, Chengbei Street,
Rugao City, Jiangsu Province – China
www.weg.net/cn
Authorised Representative in the UK:
WEG (UK) Ltd
Broad Ground Road, Lakeside, Redditch, Worcestershire B98 8YP
Contact person: Patrick O’Neill
(Single Contact Point)
www.weg.net/uk
Signed for and on behalf of the manufacturer:
Declaration of Conformity
Rodrigo Fumo
Engineering Director
Jaraguá do Sul
August 23, 2022
Carlos Lourenço
Product Compliance Supervisor
Jaraguá do Sul
August 23, 2022
To Next Page
Loading...
