10 of 10
Document Number: 9295087 03/12/2021
Subject: BIC Tune Up 2021 (USA)
Verify operation with manager? Step 2 page 2. Note manager concerns:
___________________________________________
___________________________________________
___________________________________________
___________________________________________
___________________________________________
___________________________________________
___________________________________________
Record rmware and recipe versions at beginning of Tune Up? Step 3 page 2.
UI SW VERSION ____________ SRB SW VERSION __________
LEFT MIXER SW ____________ RIGHT MIXER SW __________
FILE __________________ MENU CONNECT __________
Replace Blender Grate O-rings? Step 8 page 2.
Pour beverage drain cleaner down the left blend chamber drain, dispense area
drain and the right blend chamber drain? Step 15 page 2.
Replaced the LMS Valves? Step 16 - Step 22 page 4.
Remove the ice bin. Step 25 & Step 26 page 4.
Rotate the shaver blade? Step 27 page 4.
Shaver blade required replacement? YES NO
Remove the ice shaver gasket from the ice bin and/or the top of the dispense area
cover? Clean the surface areas? Step 28 page 4.
Wash, rinse, and sanitize the ice bin? Step 29 page 4.
Replace the shaver gasket? Step 30 page 4.
Pour beverage drain cleaner down the ice condensate bowl drain opening? Step 32
page 5.
Replaced the shaver belt? Step 37 & 38 on page 5.
Replace the CO and Water supply line O-rings? Step 41 & 42 on page 6.
Clean the condenser coil? Step 43 page 6.
Clean the condensate pan? Step 44 page 6.
Clean the condensate drain line? Step 45 page 6.
Pour hot water down drain openings of the ice bin, right blend chamber, dispense
area, and left blend chamber? Step 47 page 6.
Work the drains by hand squeezing out any buildup? Step 49 - 50 on page 6.
Connect water, CO, drain, and power cord? Step 53 page 6.
Rear drain line connected correctly to store drain? YES NO
Set the water pressure regulator to 35 psi dynamic? Step 54 page 6.
Set the CO pressure regulator to 35 psi dynamic? Step 54 page 6.
Re-install all exterior panels? Step 56 page 7.
Retrieve product from the walk in cooler and return to the BIC refrigerated cabinet?
Step 57 page 7.
Verify and assign avor slot assignments in accordance to McDonald’s Corporate?
Step 57 page 7.
Complete the Zone 2 cleaning? Step 58 page 7.
Complete “BIC UI Update Instructions”. Step 59 page 7.
Record rmware and recipe versions after UI 4.0.10 installation? Step 60 page 7.
UI SW VERSION ____________ SRB SW VERSION __________
LEFT MIXER SW ____________ RIGHT MIXER SW __________
FILE __________________ MENU CONNECT __________
Record “DRINKS SINCE INSTALLATION”? Step 64 page 7.
LEFT MIXER COUNT _________ TOTAL COUNT ____________
RIGHT MIXER COUNT _________
Perform calibration for all avors, water, and ice? Step 67 page 8.
Reset “LAST MAINTENANCE DATE”? Step 68 page 8.
Record “DRINKS SINCE LAST MAINTENANCE DATE” after new blender shafts
installed. Step 83 page 9.
LEFT MIXER COUNT _________ TOTAL COUNT ____________
RIGHT MIXER COUNT _________
Make samples of drinks with manager present. Step 84 page 9.
Both blender shafts replaced? YES NO
Fax or email completed Tune Up Checklist to the RISE Group at 920-683-
7592 or rise.callcenter@welbilt.com
Submit claim for service work through Multiplex Claims Processing System.
Tune Up Checklist MUST be attached to claim or claim will be DENIED.
Technician Signature: Date:
Technician Printed Name: Time In:
Service Agent: Time Out:
By signing this you agree that the Preventive Maintenance has been done completely and is satisfactory.
Store Manager/Operator Signature: Date:
Store Manager/Operator Printed Name: Time:
CHECKLIST
Store #
Store Address
Store Phone #
Serial Number
Model
To Previous Page
Loading...
