Welch Allyn ABPM 7100 User Manual (English)

Other manuals for Welch Allyn ABPM 7100

Instructions For Use484 pages

Quick Start Guide4 pages

Questions and Answers:

A
annamcdowellAug 22, 2025
What to do if my Welch Allyn Blood Pressure Monitor shows Err 5 bAtt?
- R
  Robert TranAug 22, 2025
  If your Welch Allyn Blood Pressure Monitor displays 'Err 5 bAtt', it means the power pack or battery voltage is too low, or the batteries are defective, or the battery contacts are corroded. Try replacing the power packs or batteries. If 'bAtt' is displayed during cuff inflation, replace the power packs. Clean corroded battery contacts with a cotton cloth and a little alcohol.
J
Jesus MorseAug 23, 2025
Why my Welch Allyn Blood Pressure Monitor cannot be switched on?
- B
  Brian JeffersonAug 25, 2025
  If your Welch Allyn Blood Pressure Monitor will not switch on, possible causes include incorrectly inserted batteries (reinsert them with correct polarity) or low battery voltage (replace the batteries).
J
Jacob WeberAug 25, 2025
What does Err 6 mean on Welch Allyn ABPM 7100 Blood Pressure Monitor?
- B
  Brian ChandlerAug 26, 2025
  If your Welch Allyn Blood Pressure Monitor displays 'Err 6' and a continuous alarm sounds, check the cuff for air build-up or kinks in the tubing, and straighten the tubing if needed. Ensure the cuff is correctly connected to the device. If there are leaks in the cuff or tubing, replace the cuff.
J
Janet MartinAug 27, 2025
How to fix faulty connection between Welch Allyn ABPM 7100 and PC?
- G
  glopezAug 27, 2025
  A faulty connection between your Welch Allyn ABPM 7100 and the PC can be due to several reasons. First, the incorrect COM interface might be set – ensure you set the correct interface in the service programs. Second, the cable plug or socket could be defective, so inspect the plug and socket on the ABPM 7100, making sure the pins are straight. Finally, the ABPM 7100 may not be in transmitting mode; switch it off and then on again without removing the connecting cable.
E
erinallenAug 27, 2025
What does Err 1 mean on Welch Allyn Blood Pressure Monitor?
- A
  April MeyersAug 27, 2025
  The 'Err 1' message on your Welch Allyn Blood Pressure Monitor can occur if the patient displays severe arrhythmia, if the arm was moved during measurement, or if there was insufficient valid pulse rate detected. Keep the arm still during measurement. Place the cuff on your arm again.
A
Anita RoblesAug 28, 2025
What does error Err 2 mean on Welch Allyn ABPM 7100?
- S
  Sally AguilarAug 29, 2025
  The 'Err 2' message on your Welch Allyn Blood Pressure Monitor indicates that the arm was moved during measurement or the cuff does not fit snugly. Keep the arm still during measurement. Check the seating of the cuff and that of the device.
A
Andrea VillanuevaAug 30, 2025
What does Err 3 mean on Welch Allyn Blood Pressure Monitor?
- S
  Shawna ClarkAug 30, 2025
  The 'Err 3' message on your Welch Allyn Blood Pressure Monitor can be caused by blood pressure beyond the measurement range, strong arm movements, or problems with the pneumatics. Keep the arm still during measurement.
B
Breanna FitzgeraldAug 31, 2025
What does Err 4 mean on Welch Allyn Blood Pressure Monitor?
- R
  ronealAug 31, 2025
  The 'Err 4' message on your Welch Allyn Blood Pressure Monitor can appear if the data transmission cable is incorrectly inserted, the pins in the plug are mechanically damaged, or the measurement value was not correctly transmitted. Insert the cable into the ABP Monitor correctly. Check the plug to see whether the pins on the inside are damaged. Restart the transmission.
E
eclarkSep 1, 2025
What does Err 7 mean on Welch Allyn ABPM 7100?
- S
  Susan PrattSep 2, 2025
  If your Welch Allyn Blood Pressure Monitor displays 'Err 7', it means the memory of the blood pressure measurement device is full. Delete the data in the ABP Monitor but ensure that the data was stored on your PC first.
M
Mark LewisSep 3, 2025
What does Code 4 mean on Welch Allyn ABPM 7100?
- L
  Laura CampbellSep 3, 2025
  If your Welch Allyn ABPM 7100 displays 'Code 4', the Bluetooth® interface of the ABPM 7100 has not yet been paired with the analysis software. Reconnect the device via Bluetooth®.

Welch Allyn ABPM 7100 Specifications

General

Device Type	Ambulatory Blood Pressure Monitor
Measurement Method	Oscillometric
Cuff Pressure Range	0-300 mmHg
Memory	Up to 300 readings
Data Transfer	USB
Systolic Range	60-270 mmHg
Mean Arterial Pressure Range	40-200 mmHg
Pulse Rate Range	40-200 bpm
Power Source	2 AA batteries
Operating Conditions	10 to 40 °C, 15 to 90% RH
Storage Conditions	10 to 95% RH
Diastolic Range	30 to 200 mmHg