Whirlpool AMD 011 User Manual

4
BEFORE USING THE APPLIANCE
To make the most out of your new appliance,
please read the user instructions carefully and keep
them handy for future consultation.
Before using the appliance please follow and
set according to the below indications:
Remote Control (RC) presetting:
Each time the batteries are replaced in the remote
control, the RC is pre-set on Heat pump.
If the air conditioner that you purchased is a
cooling only, then the pre-set on Heat pump will
not bring any changes.
Auto-Restart presetting Function:
To set the auto-restart function, press the
Emergency button (ON/OFF) on the indoor unit
for at least 5 seconds
A buzz sound will signal that the auto-restart
function is set and the air conditioner is in standby.
To cancel the auto-restart function, repeat the
above steps.
SAFETY PRECAUTIONS
• Do not install the appliance if it is connected to
the power supply.
• The Installation and service/repair must be
performed by a qualified technician, in
compliance with the producer's instructions and
following local safety norms. Do not repair or
replace any parts of the appliance unless it is
specifically written in the user instructions.
• The grounding of this appliance is compulsory.
• Make sure that the power supply cord is long
enough to allow the right connection. Do not
use any extension cord for power supply.
• Do not pull the power supply cord to remove it
from the socket.
• Do not twist or press the power supply cord,
and make sure it is not broken.
• Once installation is completed, the electric
components must not be accessible to the users.
• Do not touch the operation buttons when your
hands are wet and don't use the appliance when
you are barefoot.
• Physically or mentally disabled people, children
and people without any experience with the
product are only allowed to use the appliance if
they have had specific training on how to
operate the appliance by a person responsible
for their security and well-being. The appliance
is not intended for use by disabled people and
very young children without supervision.
Downloaded from AC-Manual.com Manuals

Whirlpool AMD 011 Specifications

General

Indoor unit weight	8000 g
Indoor units quantity	1
Indoor unit dimensions (WxDxH)	770 x 179 x 240 mm
Indoor unit noise level (high speed)	35 dB
Outdoor unit weight	26000 g
Outdoor unit noise level	52 dB
Outdoor unit dimensions (WxDxH)	715 x 240 x 482 mm
Type	Split system
Compressor type	Rotary
Remotely operated	Yes
Refrigerating medium	R410A
Cooling capacity (max)	9000 BTU/h
Dehumidifying capacity	1.2 l/h
Heating capacity (max)	9400 BTU/h
Air conditioner functions	cooling, heating
Cooling capacity in watts (max)	2638 W
Heating capacity in watts (max)	2755 W
Cooling energy efficiency (EER, W/W)	10.96
Heating energy efficiency (COP, W/W)	3.41
Airflow	420 m³/h
Power requirements	220 - 240 V, 50 Hz
Power consumption (cooling) (max)	821 W
Power consumption (heating) (max)	808 W

Summary

Before Using the Appliance

Safety Precautions

Air Conditioner Precautions

Remote Control Functions and Indicators

Operating Mode Description

Selecting Mode

Explains how to cycle through cooling, dry, fan, and heating modes.

Fan Mode

Details fan speed selection and its availability in different modes.

Setting Temperature

Instructions on adjusting the desired temperature up or down.

Turning On

Airflow Direction Control

Vertical Airflow Control

Swinging Airflow

Desired Direction Airflow

Horizontal Airflow Control

Mode and Function Descriptions

6th Sense Mode

Sleep Mode

Jet Mode

Timer Function

Maintenance

Unit

Air Filter

Protection

Features of Protection Device

Troubleshooting

Installation Instructions

Select the Best Location

Location for Installing Indoor Unit

Recommendations for choosing the optimal placement for the indoor unit.

Location for Installing Outdoor Unit

Guidelines for selecting a suitable location for the outdoor unit.

Indoor Unit Installation

Installing the Mounting Plate

Steps for mounting the plate securely on the wall.

Drill a Hole for Piping

Instructions for drilling a wall hole for refrigerant pipes and cables.

Indoor Unit Piping Installation

Connecting pipes and cables for the indoor unit.

Piping Connection

Connecting the Cable

Cable Specifications

Wiring Diagram

Power Supply from Indoor Unit, including 7K,9K, 12K, Model

Wiring diagram for heat pump models, showing indoor to outdoor connections.

Power Supply from Indoor Unit, including 18K Model

Power Supply from Outdoor Unit, including 24K Model

Outdoor Unit Installation

Install Drain Port and Drain Hose

Installing drain port and hose for condensate water in heating mode.

Install and Fix Outdoor Unit

Instructions for securely fixing the outdoor unit to the floor or wall.

Outdoor Unit Piping Connection

Connecting refrigerant pipes to the 2-way and 3-way valves.

Outdoor Unit Cable Connection

Connecting the power cables to the outdoor unit.

Air Purging

Process of removing air and moisture from the refrigeration cycle using a vacuum pump.

How to Purge Air Tubes