Windsor CS26 - User Manual

Other manuals for Windsor CS26

Questions and Answers

C
Carl FoxAug 18, 2025
How to troubleshoot no power on my Windsor CS26?
- J
  Jasmine BoydAug 18, 2025
  If your Windsor Scrubber has no power, several things could be the cause. First, check all battery cable connections to ensure they are secure. The emergency shut-off may be activated, so try resetting it. Corroded battery cables can also prevent power, so clean the connections. Other potential issues include a faulty key switch (which would need replacing), the on-board charger being plugged in (unplug it and stow the cord), or a tripped main circuit breaker (reset it).
K
kbaileyAug 21, 2025
What to do if my Windsor Scrubber has poor water pickup?
- L
  Larry MurphyAug 21, 2025
  If your Windsor Scrubber isn't picking up water, start by checking the squeegee for any caught debris and remove it. Inspect the squeegee blades for wear; rotate or replace them if needed. A clogged vacuum hose can also cause this issue, so clear any obstructions. Ensure the vacuum hose is securely connected to both the squeegee and the recovery tank dome. Clean the recovery tank float system if it's dirty. Make sure the recovery tank is sealed properly by latching the lid and replacing any damaged gaskets. If the tank is full, the float-ball shut-off may be engaged, so empty the recovery tank. Finally, if foam is filling the recovery tank, empty it and consider using less or a different detergent, or add a defoamer.
D
David ColemanAug 23, 2025
Why does my Windsor CS26 Scrubber have little or no propel?
- B
  Bradley MorenoAug 23, 2025
  If your Windsor Scrubber has little or no propel, there are several potential causes. Start by ensuring the battery is fully charged. If the machine was turned on with the pedal not in neutral, allow the pedal to return to neutral and restart the machine. Check for a tripped circuit breaker and reset it if necessary. If the wheels are spinning, decrease the brush pressure. If the controller has overheated, allow a cool down period. Inspect for a loose motor connection by checking the wires and connections from the controller to the motor. Also, check the wires and connections from the potentiometer resistance, as well as the wires, connections, and switch for both the drive reset circuit and platform circuit.
J
joshua67Aug 26, 2025
How to improve the scrubbing performance of my Windsor Scrubber?
- J
  Jessica MorrisAug 26, 2025
  If your Windsor Scrubber's scrubbing performance is poor, start by checking the scrub brushes for any caught debris and remove it. Replace worn brushes or pads. Note that using an improper detergent, brush, or pad can affect scrubbing performance, so contact equipment or application specialists. Also, ensure that the battery is fully charged.
R
Ryan JohnsonAug 28, 2025
What to do if there is little or no solution flow to the floor with my Windsor CS26 Scrubber?
- J
  Jonathan RoachAug 28, 2025
  If your Windsor Scrubber has little or no solution flow to the floor, first check if the solution tank is empty and fill it if needed. Next, inspect the solution strainer for any clogs and clean it. Also, check the solution system plumbing for obstructions and clear them. Finally, the solution solenoid valve may be obstructed or faulty, so repair or replace it as necessary.
D
Dwayne ArellanoAug 30, 2025
Why is the vacuum motor on my Windsor Scrubber not running or running slowly?
- E
  Edward YoungAug 30, 2025
  If the vacuum motor on your Windsor Scrubber doesn't run or runs slowly, inspect the vacuum circuit and switch, checking wires, connections, and the motor itself. Also, check the vacuum motor brushes for wear and replace them if needed, and inspect the commutator.
D
damonhuntSep 2, 2025
What causes the brush motors on my Windsor CS26 to not run or run slowly?
- K
  Kelly WelchSep 2, 2025
  If the brush motors on your Windsor Scrubber do not run or run slowly, ensure the battery is charged. Check the wires, connections, and motor for any issues in the brush circuit or motor itself. Also, inspect the brush motor brushes for wear and replace them if necessary, checking the commutator as well.
C
Clifford TravisSep 5, 2025
Why is the chemical metering system not operating on my Windsor CS26 Scrubber?
- S
  Stanley TorresSep 5, 2025
  If the chemical metering system on your Windsor Scrubber isn't working, start by checking if the chemical reservoir is empty and fill it if necessary. Inspect the chemical cap strainer for clogs and clean it. Clear any obstructions in the chemical system plumbing. If the flow meter is faulty, press the prime button; if chemical flows, repair or replace the flow meter. If the chemical pump is faulty, press the prime button; if chemical does not flow, repair or replace the pump.
R
Rebecca BakerSep 7, 2025
What to do if the squeegee on my Windsor CS26 Scrubber will not go up or down?
- A
  Amy WagnerSep 7, 2025
  If the squeegee on your Windsor Scrubber won't move up or down, check the wires, connectors, and actuator for any issues in the circuit or actuator itself. Also, inspect the cables and pulleys for faults and repair or replace them as needed.
R
Robin WilsonSep 9, 2025
Why does the scrub deck on my Windsor Scrubber go down, then raise?
- P
  Pamela JensenSep 9, 2025
  If the scrub deck on your Windsor Scrubber goes down and then raises, check the wire connections and actuator for any faults in the actuator circuit or the actuator itself. Also, make sure brushes or pad drivers are installed on the machine.