Woods RT60.40 - Page 29

Parts 29
MAN1177
(
07/28/2023
)
RT42.30/RTR42.30 & RT48.30/RTR48.30 ROTARY TILLER ASSEMBLY
REF
RT/RTR42.30
PART
RT/RTR48.30
PART QTY DESCRIPTION
15 1034983 1034983 1 Snap ring, external, 40 mm
16 1031925 (20) 1031925 (24) 1/2 NC x 1-1/4 HHCS, GR8 w/ shank
17 33661 33661 2 Category 1 mounting pin, w/ nut & lock washer
17A 30007 30007 2 Nut, hex 7/8 NF
17B 30008 30008 2 Washer, lock 7/8
18 1002048 1002048 1 Clutch shield
19 1042364 1042364 1 Drive assembly, complete (see page 32)
20 104391542 104391548 1 Rotor shaft
21 1043917 1043917 1 End plate
22 1043920 1043920 1 Gearbox mount
23 1043918 1043918 1 Bearing cover
24 3231 3231 * 1 3/8 NC x 2 HHCS, GR5
25 14350 14350 * 2 3/8 NC ange lock nut
26 W73163 W73163 * 2 5/16 NC ange whiz nut
27 839 839 * 1 3/8 NC x 1 HHCS, GR5
28 H019 H019 1 Lock pin, 3/8 x 2-1/4
29 104235042 104235048 1 Shield, rubber (Reverse Tillers only)
30 104391342 104391348 1
Clamp, rubber shield, right
(Reverse Tillers only)
31 1043912 1043912 1
Clamp, rubber shield, center
(Reverse Tillers only)
32 104391442 104391448 1 Clamp, rubber shield, left (Reverse Tillers only)
33 1043088 1043088 2 Gasket
35 S1042303 1042303 1 Seal, 40 x 70 x 10
36 1042352 1042352 1 Bearing asy, 6208 w/ seal
37 1031226 (20) 1031226 (24) 1/2 NC ange spiralock
38 39254 39254 4 M8-1.25P x 14 mm HHCS, CL8.8
39 35155 35155 * 4 5/16 SAE at washer
40 2472 2472 * 4 5/16 lock washer
41 44638 44638 1 Chain, 1/4 proof coil, 16 link
42 14139 14139 * 8 5/16 NC ange lock nut
43 1026530 1026530 1 Manual storage tube
44 1972 1972 * 1 1/4-28 tapered thread grease tting
45 3379 3379 * 10 1/2 NC x 1-1/2 HHCS, GR5
46 6100 6100 * 6 1/2 NC x 1-1/4 HHCS, GR5
47 25475 25475 * 10 1/2 NC x 1 HHCS, GR5, full thread
48 11900 11900 * 22 1/2 NC ange lock nut
49 16148 16148 * 2 5/16 NC x 3/4 carriage bolt, GR5
50 57816 57816 4 1/2 SAE at washer, hardened
51 24576 24576 * 2 1/2 NC x 1-3/4 HHCS, GR5
52 51243 51243 * 9 5/16 NC x 1 carriage bolt, GR5
53 1034984 1034984 1 Snap ring, internal, 80 mm
54 20891 20891 1 Ball bearing, 6208
55 15007 15007 * 1 3/4 NC x 3-1/2 HHCS, GR5
56 1002018 1002018 1 Sleeve, .81 x 1.25 x 2.12
57 2371 2371 * 1 3/4 NC hex lock nut
58 1043922KK 1043922KK 1 RT Tiller model decal set (not shown)
59 1043923KK 1043923KK 1 RT Reverse Tiller model decal set (not shown)
60 1031976 1031976 1 RT Tiller safety decal set (not shown)
HHCS Hex Head Cap Screw
* Standard hardware; obtain locally