❸
Please use
SDHC (Secure Digital High Capacity)
with a maximum capacity lower than
32GB
.
Adapter:
Used to convert
110V-240V AC to 24V DC
to provide power to the printer.
DC socket:
Located at the right rear of the printer
,
is the power socket to connect the printer and the
adapter.
Notice:
❶
Do not use a non-original power adapter to avoid danger.
❷
Please plug in the print DC socket before powering on the adapter. Do not plug in the DC socket after the
adapter is powered.
Light board:
Provide UV light to cure the liquid resin in the tank.
Notice:
❶
Do not look directly at the UV light emitting from the light board. Wear goggles if do it.
❷
Please ensure that the fan works normally when the light board is working to avoid damage to the
machine caused by excessive temperature.
Shading tape:
Used to block the unrequired UV light around the LCD screen.
LCD screen:
Used to display the section pattern of the printed model and cooperate with the UV light to cure the
resin.
Notice:
❶
The LCD screen is extremely fragile
,
please be careful.
❷
If the tank leaks out and causes the resin to ow out and cured on the LCD screen
,
please carefully remove the
cured resin residue before the next printing.
❸
Make sure that there are no resin residues on the LCD screen to block UV light.
❹
If the print failed
,
please clean the residual resin in the tank and aluminum plate in time to avoid crushing the
LCD screen when printing next time.
❺
Make sure the printing platform is properly leveled when printing
,
so as to avoid damage to the LCD screen.
❻
Please ensure that the FEP lm is close to the LCD screen to avoid affecting the print quality.
❼
Make sure that the black tape completely block the unrequired UV light around the LCD screen.
Screw motor:
Used to drive the lifting cantilever move up and down
.
20
Important Definition
Copper nut:
For working with screw motors.
Guide rail:
For linear motion guidance.
lifting cantilever:
Motor and guide rail control its up and down during printing.
Notice:
❶
Do not block the rotation of the screw motor.
❷
Do not over-tighten the mounting screws of the copper nut.
❸
Do not drop resin and other debris on the guide rail and the screw that interfere with its work.
❹
Please add grease to the screw
,
copper nut and guide rail in time to avoid excessive abrasion.
❺
Do not drop the resin on the bafe. If it is accidentally dropped
,
please clean it in time.
Photosensitive resin:
Liquid light curing resin for printer use.
Notice:
❶
Do not touch the skin directly with the resin. Wear gloves when handling. If skin contact occurs
,
wash
it with soapy water. If you feel unwell
,
please consult a doctor.
❷
The resin remaining after printing
,
if it would not be used for a long time
,
please keep it in cool and dark place.
❸
Shake the resin evenly before use.
❹
Do not eat the printed model and the resin used for printing.
❺
Keep the resin out of reach of children and pets.
❻
Do not drop the resin on any parts other than the tank and aluminum plate.If it is dropped
,
please clean it in
time.
❼
Use of third-party color paste or other dyes may result in printing failure or damage to the printer.
Working panel:
Panel for mounting components such as LCD screens and tank.
Hexagonal wrench:
Big hex wrench and small hex wrench for hex screws.
Trigger piece:
Used to trigger photoelectric switch.
Photoelectric switch:
Used to determine if the platform has reached the lowest point.
Notice:
❶
Do not block the photoelectric switch
,
otherwise the photoelectric switch will not be triggered.
21
Important Definition
To Next Page
Loading...
Need help?
General