What to do if X-Rite Measuring Instruments calibration procedure fails?
If the calibration procedure fails on your X-Rite Measuring Instruments, the calibration reference may be dirty or damaged. Clean the reference, following the appropriate procedure. If it is damaged, replace it.
How to fix X-Rite Ci64 calibration failure?
If the calibration procedure fails on your X-Rite Measuring Instrument, it might be due to a dirty or damaged calibration reference. Clean the reference following the procedure in Appendix, or replace it if it's damaged.
Why are my X-Rite Measuring Instruments measurements inaccurate?
Inaccurate measurements from your X-Rite Measuring Instruments may occur if a measurement or calibration has failed. If this happens, clean the instrument optics and calibration reference. Then, turn the instrument off and on again.
What to do if X-Rite Measuring Instruments and software are not communicating?
If your X-Rite Measuring Instruments and software aren't communicating, ensure the interface cable is correctly connected between the computer and the instrument. Then, close and restart the software application. If the problem persists, reboot the computer. Remove and reapply power to the instrument. Also, check for the correct configuration settings from the software provider.
How to fix X-Rite Measuring Instruments repeated sample measurement failures?
To resolve repeated sample measurement failures with your X-Rite Measuring Instruments, first, ensure that the sample is being read according to your software’s documentation. Then, close and restart the software application. Finally, perform a calibration on the instrument.
What to do if my X-Rite Measuring Instruments is not responding?
If your X-Rite Measuring Instruments is not responding, it could be due to a very low or bad battery pack. Try charging the battery. If the battery pack is faulty, replace it. Alternatively, ensure that the battery pack is installed or that the AC adapter is plugged in.
What to do if X-Rite Measuring Instruments navigation control buttons are non-responsive?
If the navigation control buttons on your X-Rite Measuring Instruments are non-responsive, turn the instrument off and then back on to reset their operation.
Why is my X-Rite Measuring Instrument not communicating with the software?
If your X-Rite Measuring Instrument isn't communicating with the software, ensure the interface cable is correctly connected between the computer and the instrument. Then, close and restart the software application. If the problem continues, reboot your computer. Remove and reapply power to the instrument. Also, verify that the configuration settings are correct within the software.
What to do if X-Rite Measuring Instrument shows measurement error?
If your X-Rite Measuring Instrument shows a measurement error or the results seem inaccurate, and the error persists, clean the instrument optics and calibration reference. You can also try turning the instrument off and then on again.
What to do if X-Rite Measuring Instrument is not responding?
If your X-Rite Measuring Instrument is not responding, showing no display or beeping during measurements, the battery pack may be very low or bad. Try charging the battery. If the battery pack is bad, replace it using the procedure in the Appendix. Alternatively, ensure that batteries are installed or the AC adapter is plugged in.
General safety warnings, transportation, and disposal guidelines for the instrument.
Details X-Rite's product warranty, exclusions, and customer responsibilities.
Instructions for turning the instrument on and off.
Information on charging the instrument's battery pack, including lifespan expectations.
Instructions for connecting the AC adapter to power the instrument.
Step-by-step guide for performing a basic sample measurement.
Step-by-step guide to access the configuration menu.
Step-by-step guide for performing white and black calibrations.
Step-by-step guide for performing UV calibration.
Steps to access the instrument's measure mode.
How to choose between QA, Compare, Strength, and Opacity measurement modes.
How to choose and view results in different colorimetric systems.
How to choose illuminant/observer combinations for measurements.
Overview of how standards are used and managed.
Steps to select a measurement standard by its name.
How to create new measurement standards on the instrument.
How to set and edit tolerance limits for standards.
Detailed instructions for taking a sample measurement.
How to interpret pass/fail and pass/warning indicators for measurements.
Steps to perform a measurement comparison.
Steps to perform a strength measurement.
Steps to perform an opacity measurement.
Detailed steps to select and execute a job.
Contact information and procedures for instrument service and support.
Procedure for cleaning the instrument's optical components.
Step-by-step guide for cleaning the ceramic plaque.
Step-by-step instructions for replacing the instrument's battery pack.
Common problems and their solutions for the instrument.
Detailed technical specifications of the instrument, including measurement capabilities and physical properties.
General| Brand | X-Rite |
|---|---|
| Model | Ci64 |
| Category | Measuring Instruments |
| Language | English |
To Next Page
