What to do if X-Rite Measuring Instruments calibration procedure fails?
If the calibration procedure fails on your X-Rite Measuring Instruments, the calibration reference may be dirty or damaged. Clean the reference, following the appropriate procedure. If it is damaged, replace it.
How to fix X-Rite Ci62 calibration failure?
If the calibration procedure fails on your X-Rite Measuring Instrument, it might be due to a dirty or damaged calibration reference. Clean the reference following the procedure in Appendix, or replace it if it's damaged.
Why are my X-Rite Measuring Instruments measurements inaccurate?
Inaccurate measurements from your X-Rite Measuring Instruments may occur if a measurement or calibration has failed. If this happens, clean the instrument optics and calibration reference. Then, turn the instrument off and on again.
What to do if X-Rite Measuring Instruments and software are not communicating?
If your X-Rite Measuring Instruments and software aren't communicating, ensure the interface cable is correctly connected between the computer and the instrument. Then, close and restart the software application. If the problem persists, reboot the computer. Remove and reapply power to the instrument. Also, check for the correct configuration settings from the software provider.
How to fix X-Rite Measuring Instruments repeated sample measurement failures?
To resolve repeated sample measurement failures with your X-Rite Measuring Instruments, first, ensure that the sample is being read according to your software’s documentation. Then, close and restart the software application. Finally, perform a calibration on the instrument.
What to do if my X-Rite Measuring Instruments is not responding?
If your X-Rite Measuring Instruments is not responding, it could be due to a very low or bad battery pack. Try charging the battery. If the battery pack is faulty, replace it. Alternatively, ensure that the battery pack is installed or that the AC adapter is plugged in.
What to do if X-Rite Measuring Instruments navigation control buttons are non-responsive?
If the navigation control buttons on your X-Rite Measuring Instruments are non-responsive, turn the instrument off and then back on to reset their operation.
Why is my X-Rite Measuring Instrument not communicating with the software?
If your X-Rite Measuring Instrument isn't communicating with the software, ensure the interface cable is correctly connected between the computer and the instrument. Then, close and restart the software application. If the problem continues, reboot your computer. Remove and reapply power to the instrument. Also, verify that the configuration settings are correct within the software.
What to do if X-Rite Measuring Instrument shows measurement error?
If your X-Rite Measuring Instrument shows a measurement error or the results seem inaccurate, and the error persists, clean the instrument optics and calibration reference. You can also try turning the instrument off and then on again.
What to do if X-Rite Measuring Instrument is not responding?
If your X-Rite Measuring Instrument is not responding, showing no display or beeping during measurements, the battery pack may be very low or bad. Try charging the battery. If the battery pack is bad, replace it using the procedure in the Appendix. Alternatively, ensure that batteries are installed or the AC adapter is plugged in.
Overview of the physical controls including navigation, measure button, and LED indicators.
Step-by-step procedure for taking a standard measurement on a flat sample surface.
Instructions on how to access and navigate the instrument's configuration settings.
Sets whether standards are automatically selected or manually chosen.
Enables or disables the creation of new standards using the instrument.
Enables or disables the NetProfiler feature for instrument compensation.
Step-by-step guide for performing essential white and black calibrations.
Specific calibration procedure for UV measurements on Ci64UV models.
Instructions to access the primary measurement screen and its options.
How to choose between different measurement modes like QA, Compare, Strength, and Opacity.
Procedure for selecting the colorimetric system for viewing measurement results.
Procedure for selecting illuminant and observer combinations for measurements.
Information on managing projects, which group related standards.
Details on how standards are managed, selected, and created on the instrument.
Procedure to select a standard by its name from a list.
Procedure to select a standard using its numerical index.
Explains how to create new standards using measurement or manual entry.
Procedure for adjusting tolerance limits for standards.
Guide to taking measurements of samples and viewing results.
How to interpret pass/fail indicators based on assigned tolerances.
Quick method for comparing current measurements against a standard without storing data.
Procedure for performing measurements to determine Contrast Ratio or Percent Opacity.
Guide to selecting, executing, and navigating through measurement steps in a job.
Procedures for cleaning the ceramic plaques and black trap of the calibration reference.
Lists common problems, their causes, and suggested solutions for instrument issues.
General| Wavelength Range | 400-700 nm |
|---|---|
| Illuminant | D65 |
| Data Interface | USB |
| Light Source | LED |
| Spectral Interval | 10 nm |
| Measurement Aperture | 8 mm |
| Measurement Area | 8 mm |
| Color Space | CIE L*a*b* |
| Short-Term Repeatability | ΔE < 0.1 |
| Battery | Lithium Ion |
| Repeatability | ΔE < 0.1 |
| Operating Humidity | 85% relative humidity (non-condensing) |
| Type | Portable Sphere Spectrophotometer |
To Next Page