What to do if my Xerox Copier Tray 5 (Bypass) printing failed?
If Tray 5 (Bypass) printing fails on your Xerox Copier, follow the instructions displayed to load paper of the correct size and instruct it to print again.
What to do if my Xerox D95 Copier is unable to print or unable to copy?
If your Xerox Copier is unable to print or copy, follow the instructions displayed on the screen. You can also check if the Printer Mode is set to Online by pressing the Machine Status button. As another measure, try turning the power switch off, firmly plugging in the power cord, and then turning the power switch back on.
Why do documents jam often in my Xerox Copier?
If documents jam often in your Xerox Copier, make sure the document feeder is loaded properly with acceptable media. Remove any sticky labels, paper clips, or tape from the documents. Properly set the document guides. Open the document feeder cover and check for pieces of paper. Set Mixed Size Originals to ON. Load the A5-size document vertically.
How to turn on the Xerox Copier if the power is not switched ON?
If the power is not switched ON in your Xerox Copier, turn the power switch on. If that doesn't work, turn the power switch off and then firmly plug in the power cord before turning it back on. Also, ensure that the power supply is between 200-240V and 15A, and that the power capacity is compatible with the machine's maximum power consumption (2.8-3.1 KVA).
What to do if Tray 5 (Bypass) printing failed on my Xerox D95?
If the Tray 5 (Bypass) printing failed on your Xerox Copier, follow the instructions displayed to load paper of the correct size and try printing again.
Why is Xerox Copier online indicator not lighting?
If the online indicator on your Xerox Copier isn't lighting up even when you try to print, turn the power off, unplug the power cord, and check the interface cable connection. Also, check the print driver and environment settings on your computer, and verify the status of the interface port in use.
Why is my Xerox Copier display dark?
If your Xerox Copier display is dark, first press the Power Saver button on the Control Panel to exit Power Saver mode. If the display is still dark, adjust the display brightness using the Brightness dial.
What to do if my Xerox Copier copies are not made at the desired size?
If copies from your Xerox Copier are not the desired size, try cleaning the document feeder glass or the document cover. Place the document directly on the document glass and put a white sheet of paper on top before copying. Ensure the document is loaded correctly and that the document guides are properly set. Straighten and reset the document, and enter the correct document size.
How to adjust the Xerox D95 Copier if copies are not made at the desired size?
If copies from your Xerox Copier are not made at the desired size, clean the document feeder glass or the document cover. Place the document on the document glass with a white sheet of paper on top before copying. Ensure the document is loaded correctly, the document guides are properly set, and the document is straightened. Also, enter the correct document size.
How to fix Xerox Copier when power is not switched ON?
First, ensure that the power switch is turned on. If it is already on, try turning the power switch off, then firmly plugging in the power cord, and turning the power switch back on. Also, verify that the power supply is between 200-240V and 15A, and that the power capacity is compatible with the machine's maximum power consumption (2.8-3.1 KVA).
General| Print Speed | Up to 95 ppm |
|---|---|
| Print Resolution | 2400 x 2400 dpi |
| First-Print-Out Time | As fast as 3.5 seconds |
| Duplex Printing | Yes |
| Standard Paper Size | A4 |
| Max Paper Size | 13 x 19 in. |
| Connectivity | Ethernet, USB |
| Finishing Options | Stapling, Hole Punching, Folding |
| Warranty | 1 year |
To Next Page
