What to do if my XLT Ovens Oven shows a 'Belt Jam' error?
If your XLT Ovens Oven displays a 'Belt Jam' error, it means the motor speed has significantly decreased below its recent minimum. First, check for any obstructions that might be causing the jam. If there are no obstructions, inspect the drive chain and sprocket to ensure they are in proper working condition. Then, perform a hard reset. If the issue persists, contact XLT.
What to do if my XLT Ovens Oven shows an 'Over Speed' error?
If your XLT Ovens Oven displays an 'Over Speed' error, it indicates that the speed is more than 30 seconds faster than the set point duration. First, perform a hard reset. If the error continues, check the LUI settings. If the settings are correct, perform a pan test to confirm them. If the error persists, contact XLT.
What to do if my XLT Ovens Oven shows an 'Under Speed' error?
If your XLT Ovens Oven is showing an 'Under Speed' error, it means the speed is more than 30 seconds slower than the set point duration. Check the drive chain and sprocket to verify they are in proper working condition. Perform a hard reset. If the error persists, check the LUI settings. If the settings are correct, perform a pan test to confirm them. If the error continues, contact XLT.
What to do if my XLT Ovens Oven displays an 'Over Temp' error?
If the XLT Ovens Oven displays an 'Over Temp' error, it means the temperature is 50F (10C) over the set point for more than 1 minute. If the user adjusts the set point lower, the alarm will inhibit until the new set point is reached. Perform a hard reset. If the error persists, contact XLT.
What to do if my XLT Ovens Oven displays an 'Under Temp' error?
If your XLT Ovens Oven displays an 'Under Temp' error, it means that once the set point is reached, the actual temperature is 15F (-9C) below the set point for more than 30 minutes. If you adjust the set point, the timer will reset. Perform a hard reset. If the error persists, contact XLT.
What to do if my XLT Ovens Oven displays a 'Main Fan High Amps' error?
If your XLT Ovens Oven displays a 'Main Fan High Amps' error, it indicates that the amperage is above the maximum level specified in the Main Fan Amp level table for 10 seconds. Check the CBI to see if it has tripped. If it has, reset the CBI. If not, perform a hard reset. If the error persists, contact XLT.
What to do if my XLT Ovens Oven displays a 'MainFanLow Amps' error?
If your XLT Ovens Oven displays a 'MainFanLow Amps' error, it means the amperage is below the minimum level specified in the Main Fan Amp level table for 10 seconds. Perform a hard reset. If the error continues, contact XLT.
What does 'Oven Probe' error mean on my XLT Ovens Oven?
If your XLT Ovens Oven displays an 'Oven Probe' error, it indicates a temperature sensor error, either open or short, with the temperature being less than 40F (4C) or greater than 700F (371C). Perform a hard reset. If the error persists, contact XLT.
What does 'PCB Temp Probe' error mean on my XLT Ovens Oven?
If your XLT Ovens Oven displays a 'PCB Temp Probe' error, it indicates a temperature sensor error, either open or short. Perform a hard reset. If the error persists, contact XLT.
What to do if my XLT Ovens Oven displays a 'Key Short' error?
If your XLT Ovens Oven displays a 'Key Short' error, it means any key has been shorted for more than 1 minute. Clean the LUI screen. Perform a hard reset. If the error persists, contact XLT.
Safety instructions and warnings for appliance use.
Safety precautions related to moving and stacking ovens.
Instructions for assembling the base for triple-stack oven configurations.
Instructions for assembling the base for single and double-stack oven configurations.
Steps to prepare the oven for lifting and transport.
Steps for safely stacking multiple oven units.
Specifies electrical hookup requirements for different oven regions.
Explains proper grounding procedures for electrical safety.
Details recommended clearances for oven placement.
Details gas connection and pressure requirements for different regions.
Instructions for securing the oven to prevent movement.
General requirements for venting gas appliances and hood installation.
Advice on consulting authorities and contractors for proper ventilation.
Procedure using smoke candles to test exhaust effectiveness.
Procedures and checks for initial oven operation.
Basic checks and common issues before troubleshooting the oven.
Factors influencing cooking performance and adjustments.
Details electrical inputs required for the VFD control box.
Details electrical outputs provided by the VFD control box.
Configuration of the VFD control box for standard models.
Procedures for setting up lifting jacks for hood installation.
Steps to safely stack the hood onto the oven units.
Method for suspending the hood from ceiling joists.
Connecting oven power and control cords to the hood's VFD box.
Procedures and checks for initial hood operation.
To Next Page
General