To Next PageTo Next PageWhat to do if my XLT Ovens Oven shows a 'Belt Jam' error?
If your XLT Ovens Oven displays a 'Belt Jam' error, it means the motor speed has significantly decreased below its recent minimum. First, check for any obstructions that might be causing the jam. If there are no obstructions, inspect the drive chain and sprocket to ensure they are in proper working condition. Then, perform a hard reset. If the issue persists, contact XLT.
What to do if my XLT Ovens Oven shows an 'Over Speed' error?
If your XLT Ovens Oven displays an 'Over Speed' error, it indicates that the speed is more than 30 seconds faster than the set point duration. First, perform a hard reset. If the error continues, check the LUI settings. If the settings are correct, perform a pan test to confirm them. If the error persists, contact XLT.
What to do if my XLT Ovens Oven shows an 'Under Speed' error?
If your XLT Ovens Oven is showing an 'Under Speed' error, it means the speed is more than 30 seconds slower than the set point duration. Check the drive chain and sprocket to verify they are in proper working condition. Perform a hard reset. If the error persists, check the LUI settings. If the settings are correct, perform a pan test to confirm them. If the error continues, contact XLT.
What to do if my XLT Ovens Oven displays an 'Over Temp' error?
If the XLT Ovens Oven displays an 'Over Temp' error, it means the temperature is 50F (10C) over the set point for more than 1 minute. If the user adjusts the set point lower, the alarm will inhibit until the new set point is reached. Perform a hard reset. If the error persists, contact XLT.
What to do if my XLT Ovens Oven displays an 'Under Temp' error?
If your XLT Ovens Oven displays an 'Under Temp' error, it means that once the set point is reached, the actual temperature is 15F (-9C) below the set point for more than 30 minutes. If you adjust the set point, the timer will reset. Perform a hard reset. If the error persists, contact XLT.
What to do if my XLT Ovens Oven displays a 'Main Fan High Amps' error?
If your XLT Ovens Oven displays a 'Main Fan High Amps' error, it indicates that the amperage is above the maximum level specified in the Main Fan Amp level table for 10 seconds. Check the CBI to see if it has tripped. If it has, reset the CBI. If not, perform a hard reset. If the error persists, contact XLT.
What to do if my XLT Ovens Oven displays a 'MainFanLow Amps' error?
If your XLT Ovens Oven displays a 'MainFanLow Amps' error, it means the amperage is below the minimum level specified in the Main Fan Amp level table for 10 seconds. Perform a hard reset. If the error continues, contact XLT.
What does 'Oven Probe' error mean on my XLT Ovens Oven?
If your XLT Ovens Oven displays an 'Oven Probe' error, it indicates a temperature sensor error, either open or short, with the temperature being less than 40F (4C) or greater than 700F (371C). Perform a hard reset. If the error persists, contact XLT.
What does 'PCB Temp Probe' error mean on my XLT Ovens Oven?
If your XLT Ovens Oven displays a 'PCB Temp Probe' error, it indicates a temperature sensor error, either open or short. Perform a hard reset. If the error persists, contact XLT.
What to do if my XLT Ovens Oven displays a 'Key Short' error?
If your XLT Ovens Oven displays a 'Key Short' error, it means any key has been shorted for more than 1 minute. Clean the LUI screen. Perform a hard reset. If the error persists, contact XLT.
General