XYZ Machine Tools ProTURN SLX 1630

Questions and Answers

B
Breanna LopezSep 2, 2025
What could cause a fault X or Z error on my XYZ Machine Tools Industrial Equipment?
- R
  Richard BuckleySep 3, 2025
  A 'Fault X or Z' error on your XYZ Machine Tools Industrial Equipment can arise from: * Switched servo cables at the pendant. Ensure the X and Z servo cables are in the correct ports. * Extremely tight X-axis Gibs. Check the adjustment of the X-axis Gibs. * Excessive friction in the slideways. * Binding or looseness in the Drive Train. * Issues with incoming electrical power. * Servo Drive failure. * Motor failure. * Computer/Pendant failure.
J
Jennifer JarvisSep 14, 2025
What causes excess gearbox noise in my XYZ Machine Tools Industrial Equipment?
- D
  douglas75Sep 15, 2025
  Excess gearbox noise in your XYZ Machine Tools Industrial Equipment can be due to: * Insufficient oil in the headstock. Check the site glass to ensure the oil is at a sufficient level. * The spindle bearing not being lubricated properly or a worn bearing. Remove the top lid and ensure oil is overflowing freely to the spindle bearings. * Loose spindle preload. Tighten spindle preload on the bearing to approximately 1.1 – 1.7 N-m.
D
Daniel BrownSep 1, 2025
Why does my XYZ Machine Tools Industrial Equipment display blank?
- D
  Diana UnderwoodSep 1, 2025
  If the display on your XYZ Machine Tools Industrial Equipment blanks, check the following: * The screen saver may have been activated. Press any key to turn it back on. All LED keys on the pendant will blink when the screen saver is on; press any key to deactivate it. * The system may have shut down. Turn the power switch off, check the computer/pendant fuses and cable connections. * There might be a poor cable connection from the Computer Module to the LCD (Liquid Crystal Display). Double-check this connection. * A fuse may be blown in the pendant. Remove the fuse and check its continuity. * The computer/pendant may have failed.
S
Samantha HendersonSep 18, 2025
Why is the spindle running backwards on my XYZ Machine Tools Industrial Equipment?
- K
  Kimberly HoffmanSep 18, 2025
  If the spindle runs backwards on your XYZ Machine Tools Industrial Equipment, it's likely due to: * Backwards 3-phase wires. Switch any 2 of the 3 wires either coming out of the Spindle Drive (T1, T2, and T3) or going into the Spindle Motor (U, V, and W). Be sure to shut off all power to the machine before attempting to switch any wires.
C
Christina HigginsSep 16, 2025
Why are X and Z-axis measurements not repeating on my XYZ Machine Tools Industrial Equipment?
- C
  Crystal WhiteSep 16, 2025
  If X and Z-axis measurements do not repeat on your XYZ Machine Tools Industrial Equipment, consider the following: * Machine tool & setup problem. Check for any looseness in the setup. * X and Z-axis Gibs are loose. Check the adjustment of the X-axis Gib. * X and Z-axis Drive Trains are loose. Inspect the Drive Train for any looseness. * The encoder disk or reader head on the motor may be loose. Swap the motor in question with a known good motor.
M
Michael JonesSep 23, 2025
How to troubleshoot XYZ Machine Tools Industrial Equipment that will not hold calibration?
- K
  Kathryn TurnerSep 23, 2025
  To troubleshoot why your XYZ Machine Tools Industrial Equipment will not hold calibration, replace the Computer/Pendant module.
E
egallagherAug 28, 2025
What causes my XYZ Machine Tools Industrial Equipment to stall or turn off during machining?
- J
  jeffrey33Aug 29, 2025
  If your XYZ Machine Tools Industrial Equipment spindle stalls or turns off during machining, consider the following: * Machine tool and setup problems related to the material being cut, the cutting tool, RPM, and feed rate. Check the cutter's condition to ensure it is not dull. * The motor drive belt may be slipping. Check the alignment, condition, and tension of the drive belt. * Cutting more than the machine is capable of. Check speeds, feeds, and depth of cut.
B
barbarafoleyAug 27, 2025
How to troubleshoot cross threading on my XYZ Machine Tools Industrial Equipment?
- J
  joshua30Aug 28, 2025
  To troubleshoot cross threading on your XYZ Machine Tools Industrial Equipment, check the following: * Looseness in the Gib. Gib adjustment may be needed. * Looseness in the drive train. Inspect the drive train diagnostics. * Calibration issues. * Failure of the spindle encoder. Run service code 133 to check if the encoder counts. Replace the spindle encoder if necessary.
A
Ashley AcostaAug 27, 2025
Why is my XYZ Machine Tools Industrial Equipment axis slowing down?
- E
  Elizabeth HaleAug 27, 2025
  If an axis on your XYZ Machine Tools Industrial Equipment is slowing down, it could be due to: * The maximum allowable Arc Accuracy being set too low. The factory default is set at 0.13 mm. Values lower than 0.13 mm may reduce the feedrate even more. * Inadequate incoming AC voltage. * Inadequate or no lubrication to ballscrews and way surfaces. Ensure proper lubrication and check for pinched or blocked oil lines. * Improperly adjusted X-axis Gib. * Binding in the Drive Train. * Servo Drive failure. * Motor failure.
D
Daniel TuckerAug 26, 2025
What to do if my XYZ Machine Tools Industrial Equipment is cutting taper?
- S
  Stephanie PeckAug 27, 2025
  If your XYZ Machine Tools Industrial Equipment is cutting a taper, consider these potential causes: * The machine may not be leveled properly. * There might be a tooling problem, such as improper tooling or workpiece support. Use a steady rest or follow rest, and reduce overhang from the chuck headstock or tailstock. * There could be looseness in the gib or misalignment of the ball screw. Gib adjustment might be needed. * Looseness in the spindle bearings could be the issue. * The headstock and/or tailstock may not be aligned.