XYZ Machine Tools ProtoTRAK SLX CNC

Questions and Answers

W
William JohnsonSep 14, 2025
What causes excess gearbox noise in my XYZ Machine Tools Industrial Equipment?
- C
  Caroline RoseSep 14, 2025
  Excess gearbox noise in your XYZ Machine Tools Industrial Equipment can be due to: * Insufficient oil in the headstock. Check the site glass to ensure the oil is at a sufficient level. * The spindle bearing not being lubricated properly or a worn bearing. Remove the top lid and ensure oil is overflowing freely to the spindle bearings. * Loose spindle preload. Tighten spindle preload on the bearing to approximately 1.1 – 1.7 N-m.
S
Sherry GarciaAug 25, 2025
What causes vibration in motion in my XYZ Machine Tools Industrial Equipment?
- A
  Annette PeckAug 26, 2025
  Vibration during motion in your XYZ Machine Tools Industrial Equipment can stem from several issues: * Too much backlash may be entered in Code 128. Recheck the machine's backlash. * There might be inadequate lubrication to ballscrews and way surfaces. Ensure proper lubrication and check the lube pump and oil lines. * The X Gib may not be making good contact. Inspect the gibs for contact, aiming for at least 80% surface contact. * Binding or looseness in the drive train can cause vibration. Inspect the drive train for these issues. * The axis motor belt might be too tight; loosen it. * There could be misalignment of the ball screw.
P
phigginsAug 26, 2025
What to do if my XYZ Machine Tools Industrial Equipment is cutting taper?
- L
  langmelissaAug 27, 2025
  If your XYZ Machine Tools Industrial Equipment is cutting a taper, consider these potential causes: * The machine may not be leveled properly. * There might be a tooling problem, such as improper tooling or workpiece support. Use a steady rest or follow rest, and reduce overhang from the chuck headstock or tailstock. * There could be looseness in the gib or misalignment of the ball screw. Gib adjustment might be needed. * Looseness in the spindle bearings could be the issue. * The headstock and/or tailstock may not be aligned.
D
Destiny GriffinAug 27, 2025
Why is my XYZ Machine Tools Industrial Equipment axis slowing down?
- J
  Joel BlanchardAug 27, 2025
  If an axis on your XYZ Machine Tools Industrial Equipment is slowing down, it could be due to: * The maximum allowable Arc Accuracy being set too low. The factory default is set at 0.13 mm. Values lower than 0.13 mm may reduce the feedrate even more. * Inadequate incoming AC voltage. * Inadequate or no lubrication to ballscrews and way surfaces. Ensure proper lubrication and check for pinched or blocked oil lines. * Improperly adjusted X-axis Gib. * Binding in the Drive Train. * Servo Drive failure. * Motor failure.
V
Vanessa TorresSep 15, 2025
Why are X and Z-axis measurements not accurate on my XYZ Machine Tools Industrial Equipment?
- H
  Heather CraigSep 15, 2025
  If X and Z-axis measurements are not accurate on your XYZ Machine Tools Industrial Equipment, it could be due to: * Incorrect calibration. Recalibrate the machine. * Incorrect backlash values. If the machine does not repeat bi-directionally, check the backlash on the axis in question.
E
Emily FloresSep 23, 2025
How to troubleshoot XYZ Machine Tools Industrial Equipment that will not hold calibration?
- M
  Michael RobertsonSep 23, 2025
  To troubleshoot why your XYZ Machine Tools Industrial Equipment will not hold calibration, replace the Computer/Pendant module.
C
Chad TorresSep 8, 2025
Why is my XYZ Machine Tools Industrial Equipment running away?
- L
  Lisa MendezSep 8, 2025
  If your XYZ Machine Tools Industrial Equipment axis is running away, it could be due to: * The home positions or tools are not set correctly. * A bad motor encoder.
J
Julie WillisSep 8, 2025
What causes every part to have the same error on my XYZ Machine Tools Industrial Equipment?
- A
  Albert JeffersonSep 9, 2025
  If every part produced by your XYZ Machine Tools Industrial Equipment has the same error, the cause might be: * A programming error where programmed dimensions are incorrect. Check absolute and incremental values. * A machine & setup related issue.
J
James HollowayNov 22, 2025
What to do if my XYZ Machine Tools Industrial Equipment has a poor finish?
- D
  Danny WilcoxNov 22, 2025
  If your XYZ Machine Tools Industrial Equipment has a poor finish, there could be several reasons: * Check if all way surfaces are getting proper lubrication. If not, ensure the lube pump is functioning correctly and inspect for pinched or blocked oil lines. * The X & Z-axis Drive Trains may be loose. Inspect the Drive Train for any looseness, disassembling and reassembling if necessary. * Way surfaces might be pocked, scarred, or excessively worn. Visually inspect all way surfaces and adjust the Gibs in affected areas, ensuring proper lubrication. * The machine’s feet may not be equally supporting weight. * There might be an improper tooling, workpiece support or incorrect speeds and feeds. * The X gib may be too tight or loose. * There could be looseness in the spindle bear...
C
Cindy RobinsonSep 1, 2025
Why does my XYZ Machine Tools Industrial Equipment display blank?
- K
  Kenneth WelchSep 1, 2025
  If the display on your XYZ Machine Tools Industrial Equipment blanks, check the following: * The screen saver may have been activated. Press any key to turn it back on. All LED keys on the pendant will blink when the screen saver is on; press any key to deactivate it. * The system may have shut down. Turn the power switch off, check the computer/pendant fuses and cable connections. * There might be a poor cable connection from the Computer Module to the LCD (Liquid Crystal Display). Double-check this connection. * A fuse may be blown in the pendant. Remove the fuse and check its continuity. * The computer/pendant may have failed.