XYZ Machine Tools ProtoTRAK SLX CNC

Questions and Answers

P
phigginsAug 26, 2025
What to do if my XYZ Machine Tools Industrial Equipment is cutting taper?
- L
  langmelissaAug 27, 2025
  If your XYZ Machine Tools Industrial Equipment is cutting a taper, consider these potential causes: * The machine may not be leveled properly. * There might be a tooling problem, such as improper tooling or workpiece support. Use a steady rest or follow rest, and reduce overhang from the chuck headstock or tailstock. * There could be looseness in the gib or misalignment of the ball screw. Gib adjustment might be needed. * Looseness in the spindle bearings could be the issue. * The headstock and/or tailstock may not be aligned.
D
Destiny GriffinAug 27, 2025
Why is my XYZ Machine Tools Industrial Equipment axis slowing down?
- J
  Joel BlanchardAug 27, 2025
  If an axis on your XYZ Machine Tools Industrial Equipment is slowing down, it could be due to: * The maximum allowable Arc Accuracy being set too low. The factory default is set at 0.13 mm. Values lower than 0.13 mm may reduce the feedrate even more. * Inadequate incoming AC voltage. * Inadequate or no lubrication to ballscrews and way surfaces. Ensure proper lubrication and check for pinched or blocked oil lines. * Improperly adjusted X-axis Gib. * Binding in the Drive Train. * Servo Drive failure. * Motor failure.
J
Jill WyattAug 27, 2025
How to troubleshoot cross threading on my XYZ Machine Tools Industrial Equipment?
- F
  fbentonAug 28, 2025
  To troubleshoot cross threading on your XYZ Machine Tools Industrial Equipment, check the following: * Looseness in the Gib. Gib adjustment may be needed. * Looseness in the drive train. Inspect the drive train diagnostics. * Calibration issues. * Failure of the spindle encoder. Run service code 133 to check if the encoder counts. Replace the spindle encoder if necessary.
G
Gail PattonAug 28, 2025
What causes my XYZ Machine Tools Industrial Equipment to stall or turn off during machining?
- C
  caseyfitzpatrickAug 28, 2025
  If your XYZ Machine Tools Industrial Equipment spindle stalls or turns off during machining, consider the following: * Machine tool and setup problems related to the material being cut, the cutting tool, RPM, and feed rate. Check the cutter's condition to ensure it is not dull. * The motor drive belt may be slipping. Check the alignment, condition, and tension of the drive belt. * Cutting more than the machine is capable of. Check speeds, feeds, and depth of cut.
M
mark08Aug 29, 2025
How do I fix incorrect dimensions on parts from my XYZ Machine Tools Industrial Equipment?
- A
  amandairwinAug 29, 2025
  If parts from your XYZ Machine Tools Industrial Equipment have incorrect dimensions, consider the following: * There might be a programming error. Check that the programmed dimensions are correct, including absolute and incremental values. * There could be a machine & setup related problem.
S
Shirley SmithAug 30, 2025
Why is my XYZ Machine Tools Industrial Equipment not threading?
- J
  jennifer81Aug 30, 2025
  If your XYZ Machine Tools Industrial Equipment is not threading, consider the following possible causes: * The spindle speed might be too fast; slow it down. * There could be a failure of the spindle encoder. Run service code 133 to check if the encoder counts. Replace the spindle encoder if necessary. * The encoder coupling may be broken or slipping. Check and replace as needed.
V
vmossAug 31, 2025
What to do if my XYZ Machine Tools Industrial Equipment has a keyboard lockup?
- M
  Mr. Timothy FernandezAug 31, 2025
  If your XYZ Machine Tools Industrial Equipment experiences a keyboard lockup, try the following: * A voltage drop/spike may have occurred. Shut down the system and wait 10 seconds to reboot it. * The Remote Stop-Go (RSG) switch may have a short (if connected). Remove the RSG, turn the system off and on again. If the problem disappears and reappears when the RSG is plugged in, replace the RSG. * There might be poor cable connections from the Computer Module to the Distribution Board and from the Distribution Board to the Keyboard. Re-seat cable connectors by pulling them out and pushing them back in. * The computer/pendant may have failed.
A
Ashley DavisAug 25, 2025
Why is my XYZ Machine Tools Industrial Equipment axis not jogging?
- S
  Shawn ThompsonAug 25, 2025
  If an axis on your XYZ Machine Tools Industrial Equipment is not jogging, consider the following: * The system may not have been booted up properly; shut down and wait 10 seconds before rebooting. * The E-Stop might be pressed in. Check the E-Stop, especially if both axes will not jog. * The E-Stop reset button may need to be pressed, located on the side of the pendant. * There could be a servo drive failure, particularly if only one axis will not jog. * The motor may be shorted. * There might be poor cable or wiring connections. * The computer/pendant may have failed.
A
Alejandro PhillipsSep 1, 2025
Why does my XYZ Machine Tools Industrial Equipment show a bad picture on the display?
- E
  Emily AlvarezSep 2, 2025
  If your XYZ Machine Tools Industrial Equipment displays a bad picture, it could be due to: * A poor cable connection from the Computer Module to the LCD (Liquid Crystal Display). Check the ribbon cable connection from the LCD screen to the computer module. * The computer/pendant may have failed.
K
Kristina DavisSep 2, 2025
What could cause a fault X or Z error on my XYZ Machine Tools Industrial Equipment?
- E
  elaine49Sep 2, 2025
  A 'Fault X or Z' error on your XYZ Machine Tools Industrial Equipment can arise from: * Switched servo cables at the pendant. Ensure the X and Z servo cables are in the correct ports. * Extremely tight X-axis Gibs. Check the adjustment of the X-axis Gibs. * Excessive friction in the slideways. * Binding or looseness in the Drive Train. * Issues with incoming electrical power. * Servo Drive failure. * Motor failure. * Computer/Pendant failure.