To Next PageTo Next PageHow do I fix incorrect dimensions on parts from my XYZ Machine Tools Industrial Equipment?
If parts from your XYZ Machine Tools Industrial Equipment have incorrect dimensions, consider the following: * There might be a programming error. Check that the programmed dimensions are correct, including absolute and incremental values. * There could be a machine & setup related problem.
What causes my XYZ Machine Tools Industrial Equipment to stall or turn off during machining?
If your XYZ Machine Tools Industrial Equipment spindle stalls or turns off during machining, consider the following: * Machine tool and setup problems related to the material being cut, the cutting tool, RPM, and feed rate. Check the cutter's condition to ensure it is not dull. * The motor drive belt may be slipping. Check the alignment, condition, and tension of the drive belt. * Cutting more than the machine is capable of. Check speeds, feeds, and depth of cut.
How to troubleshoot cross threading on my XYZ Machine Tools Industrial Equipment?
To troubleshoot cross threading on your XYZ Machine Tools Industrial Equipment, check the following: * Looseness in the Gib. Gib adjustment may be needed. * Looseness in the drive train. Inspect the drive train diagnostics. * Calibration issues. * Failure of the spindle encoder. Run service code 133 to check if the encoder counts. Replace the spindle encoder if necessary.
Why is my XYZ Machine Tools Industrial Equipment axis slowing down?
If an axis on your XYZ Machine Tools Industrial Equipment is slowing down, it could be due to: * The maximum allowable Arc Accuracy being set too low. The factory default is set at 0.13 mm. Values lower than 0.13 mm may reduce the feedrate even more. * Inadequate incoming AC voltage. * Inadequate or no lubrication to ballscrews and way surfaces. Ensure proper lubrication and check for pinched or blocked oil lines. * Improperly adjusted X-axis Gib. * Binding in the Drive Train. * Servo Drive failure. * Motor failure.
What to do if my XYZ Machine Tools Industrial Equipment is cutting taper?
If your XYZ Machine Tools Industrial Equipment is cutting a taper, consider these potential causes: * The machine may not be leveled properly. * There might be a tooling problem, such as improper tooling or workpiece support. Use a steady rest or follow rest, and reduce overhang from the chuck headstock or tailstock. * There could be looseness in the gib or misalignment of the ball screw. Gib adjustment might be needed. * Looseness in the spindle bearings could be the issue. * The headstock and/or tailstock may not be aligned.
What causes vibration in motion in my XYZ Machine Tools Industrial Equipment?
Vibration during motion in your XYZ Machine Tools Industrial Equipment can stem from several issues: * Too much backlash may be entered in Code 128. Recheck the machine's backlash. * There might be inadequate lubrication to ballscrews and way surfaces. Ensure proper lubrication and check the lube pump and oil lines. * The X Gib may not be making good contact. Inspect the gibs for contact, aiming for at least 80% surface contact. * Binding or looseness in the drive train can cause vibration. Inspect the drive train for these issues. * The axis motor belt might be too tight; loosen it. * There could be misalignment of the ball screw.
General| Brand | XYZ Machine Tools |
|---|---|
| Model | ProTURN SLX 1630 |
| Category | Industrial Equipment |
| Language | English |
Lists safety publications relevant to the manual.
Provides essential safety rules and warnings for operating the machine.
Details the physical space and layout needed for machine installation.
Step-by-step guide for installing the machine and a checklist for verification.
Technical specifications and dimensions of the SLX 1630 machine.
Instructions for ensuring the machine is properly leveled for accurate operation.
Details on how to connect the machine to the electrical power supply.
Diagnosing issues affecting the quality of machined parts.
Troubleshooting axis movement and positional errors.
Resolving issues with the machine's control interface and software.
Addressing inaccuracies or inconsistencies in measurement readings.
Identifying and resolving mechanical or operational faults of the machine itself.
General checks and setup procedures for diagnosing machine issues.
Diagnosing problems related to the machine's mechanical drive systems.
Troubleshooting issues with the computer and pendant interface.
Procedures for diagnosing motor-related faults and issues.
Explains how to access and use various service codes for diagnostics and setup.
Step-by-step guides for replacing major machine components.
Routine maintenance tasks to ensure optimal machine performance.
Installation and troubleshooting for the Dorian indexer.
Installation and troubleshooting for the 4-tool indexer.
Comprehensive list of parts for the SLX 1630 machine.
Specific parts list for the headstock assembly.
Exploded view and parts list for the tailstock assembly.
