14
Squelch Preset Threshold (THLD SQL)
m Inject a –15.0 dBµ RF signal (1 kHz tone @ ±3.5 kHz
deviation), then press the V/M button, then press the
MON/F button twice. Press the V/M button, then rotate
the DIAL to select the next setting.
Squelch Preset Tight (TIGH SQL)
m Adjust the generator level to –4.0 dBµ, then press the V/M
button, then press the MON/F button twice. Press the V/
M button, then rotate the DIAL to select the next setting.
S-Meter S-1 Adjustment (S1 LEVEL)
m Adjust the generator level to –7.0 dBµ (1 kHz tone @
±3.5 kHz deviation), then press the V/M button, then
press the MON/F button twice. Press the V/M button,
then rotate the DIAL to select the next setting.
S-Meter Full-Scale Adjustment (S9 LEVEL)
m Adjust the generator level to +19 dBµ (1 kHz tone @
±3.5 kHz deviation), then press the V/M button, then
press the MON/F button twice. Press the V/M button,
then rotate the DIAL to select the next setting.
Wide-FM S-Meter S-1 Adjustment (S1 LEVEL)
m Adjust the generator level to 0 dBµ (1 kHz tone @ ±20
kHz deviation), then press the V/M button, then press
the MON/F button twice. Press the V/M button, then
rotate the DIAL to select the next setting.
Wide-FM S-Meter Full-Scale Adjustment (S9 LEVEL)
m Adjust the generator level to +20 dBµ (1 kHz tone @
±20 kHz deviation), then press the V/M button, then
press the MON/F button twice. Press the V/M button,
then rotate the DIAL to select the next setting.
The alignment frequency will now be automatically set
to 50.000 MHz.
High TX Power Adjustment (HI POWER)
m Transmit, and adjust the output power level for 5.0 W
(±0.3 W) by rotating the DIAL, then press the V/M but-
ton. Rotate the DIAL to select the next setting.
L3 Tx Power Adjustment (L3 POWER)
m Transmit, and adjust the output power level for 2.5 W
(±0.2 W) by rotating the DIAL, then press the V/M but-
ton. Rotate the DIAL to select the next setting.
L2 Tx Power Adjustment (L2 POWER)
m Transmit, and adjust the output power level for 1.0 W
(±0.1 W) by rotating the DIAL, then press the V/M but-
ton. Rotate the DIAL to select the next setting.
L1 Tx Power Adjustment (L1 POWER)
m Transmit, and adjust the output power level for 50 mW
(+50/-30 mW) by rotating the DIAL, then press the V/M
button. Rotate the DIAL to select the next setting.
TX Deviation Adjustment (MAX DEV)
m Inject a 1 kHz audio tone at a level of 50mV (rms) to the
MIC jack. Press the V/M button, then transmit and ad-
just the deviation for4.5 kHz (±0.2 kHz) (USA Version:
(4.2 ±0.2 kHz)) by rotating the DIAL, then press the V/M
button. Rotate the DIAL to select the next setting.
AM Modulation (AM MOD)
m Inject a 1 kHz audio tone at a level of 100 mV (rms) to
the MIC jack. Press the V/M button, then transmit and
adjust the modulation for 60% (±10%) by rotating the
DIAL, then press and hold in the MON/F button for
one second.
CTCSS Tx Deviation Adjustment (TN 67.0)
m Press the V/M button, then transmit and adjust the de-
viation for 0.5 kHz (+0.05/-0.1 kHz) by rotating the
DIAL, then press the V/M button. Rotate the DIAL to
select the next setting.
CTCSS Tx Deviation Adjustment (TN 183.5)
m Press the V/M button, then transmit and adjust the de-
viation for 0.5 kHz (±0.1 kHz) by rotating the DIAL,
then press the V/M button. Rotate the DIAL to select
the next setting.
CTCSS Tx Deviation Adjustment (TN 254.1)
m Press the V/M button, then transmit and adjust the de-
viation for 0.5 kHz (±0.1 kHz) by rotating the DIAL,
then press the V/M button. Rotate the DIAL to select
the next setting.
DCS Tx Deviation Adjustment (DCS DEV)
m Press the V/M button, then transmit and adjust the de-
viation for 0.6 kHz (±0.1 kHz) by rotating the DIAL,
then press the V/M button. Rotate the DIAL to select
the next setting.
Press the MON/F button to activate the TX Power and
Deviation alignment routine.
The alignment frequency will automatically be set to
54.000 MHz.
High TX Power Adjustment (HI POWER)
m Transmit, and adjust the output power level for 5.0 W
(±0.3 W) by rotating the DIAL, then press the V/M but-
ton. Rotate the DIAL to select the next setting.
Alignment
To Next Page
Loading...
Need help?
General
