What to do if my Yamaha CRX-332 fails to turn on?
First, ensure the power cable is firmly connected. If the issue persists, it may be due to an external electric shock. In that case, press and hold the power button for more than 5 seconds to reset the system. If that doesn't work, put the unit in standby mode, disconnect the power cable, wait 30 seconds, reconnect it, and then try using it normally.
Why is FM stereo reception noisy on my Yamaha Receiver?
Check the antenna connections to ensure they are properly connected. If the transmitter is too far away or the antenna input is poor, try using a high-quality directional FM antenna.
Why is sound only coming from one speaker on my Yamaha CRX-332 Receiver?
Check the cable connections to ensure they are properly connected. If the problem continues, the cables may be defective. The unit might be too close to digital or high-frequency equipment; move it farther away. Also, check if the AUTO POWER OFF is triggered, setting AUTO POWER OFF to TIME OFF enables continuous play.
What to do if my Yamaha Receiver displays 'No Disc'?
The disc might be incompatible with the unit. Remove the disc and check if the unit supports that type of disc. The disc may be dirty; try wiping it clean. Ensure the disc is loaded with the labeled side facing up. If the unit was moved from a cold to a warm place, condensation may have formed on the lens; wait one or two hours for the unit to adjust to room temperature and try again.
What to do if my Yamaha CRX-332 Receiver power is suddenly turned off?
If your Yamaha Receiver suddenly turns off, it could be due to the sleep timer being set. Turn the unit back on and resume playback. Also, the unit will turn off if left on for 1 hour without playback.
How to fix a Yamaha CRX-332 that fails to turn on?
If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, check that the power cable is securely connected. If the issue persists, the unit may have experienced an external electric shock. To resolve this, press and hold the power button for more than 5 seconds to reset the system. If that doesn't work, put the unit in standby mode, unplug the power cable, wait 30 seconds, plug it back in, and then try using it normally.
What to do if my Yamaha Receiver has no sound?
If your Yamaha Receiver isn't producing any sound, ensure that you've selected the correct input source using the INPUT button on the front panel or the source buttons on your remote control. It is possible that the selected source component sends signals that the unit cannot reproduce.
What to do if my Yamaha CRX-332 suddenly turns off?
The sleep timer may be activated. Turn the unit back on and resume playback. Also, the unit automatically turns off if left on for 1 hour without any operation.
What to do if my Yamaha CRX-332 Receiver remote control does not work?
The remote control sensor on the Yamaha Receiver might be exposed to direct sunlight or strong lighting; try adjusting the lighting or the receiver's orientation. Also, make sure you are within the remote's operational range. Check for any obstacles between the remote and the receiver's sensor and remove them. Finally, the batteries in the remote might be worn out, so try replacing them with new ones.
Why is there no sound coming from my Yamaha CRX-332?
There could be several reasons for this. Ensure that you have selected the appropriate input source using the INPUT button on the front panel or the source buttons on the remote control. Also, the unit might be off, so connect the power cable correctly. Another possible cause is that the signals from your source component cannot be reproduced by this unit.
General| Receiver type | stereo |
|---|---|
| Audio output channels | 2.0 channels |
| Total Harmonic Distortion (THD) | 0.04 % |
| Power output per channel (1KHz@6 Ohm) | 20 W |
| Power output per channel (20-20KHz@8 Ohm) | - W |
| HDMI in | - |
| Audio (L/R) in | 1 |
| Banana connector | 4 |
| Connectivity technology | Wired |
| Speakers connectivity type | Binding post |
| Audio formats supported | MP3, WMA |
| Ethernet LAN | No |
| Supported radio bands | AM, FM |
| Preset stations quantity | 60 |
| Optical drive type | CD player |
| Disc types supported | CD, CD-R, CD-RW |
| Optical drive included | Yes |
| Product color | Black |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Apple docking compatibility | iPod |
| Power consumption (standby) | 0.3 W |
| Power consumption (typical) | 32 W |
| Package weight | 4500 g |
| Package depth | 397 mm |
| Package width | 279 mm |
| Package height | 200 mm |
Weight and Dimensions| Depth | 317.5 mm |
|---|---|
| Width | 181 mm |
| Height | 117.5 mm |
| Weight | 2950 g |
Reduce risk of fire or electric shock by avoiding rain or moisture.
Only qualified personnel should service this device due to laser use.
Avoid direct eye exposure to laser beam when unit is open or plugged in.
Lists compatible disc types including CD, CD-R/RW, and CD-TEXT.
Procedure for connecting speakers, FM antenna, and subwoofer.
Procedures for playing music from iPod, iPad, USB, and CD.
Common problems and solutions for the unit not turning on, operating, or having no sound.
Troubleshooting specific issues related to iPod and iPad connections and operation.
Solutions for problems like no sound, distorted sound, or discs not playing.
Troubleshooting for USB device recognition, playback, and file format issues.
Solutions for noisy FM reception, tuning issues, and preset function errors.
Troubleshooting steps for remote control malfunctions, range, and battery issues.
To Next Page
