EasyManuals Logo

Yamaha DBR Series Service Manual

Yamaha DBR Series
109 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #50 background imageLoading...
Page #50 background image
50
DBR10/DBR12/DBR15
2-15.
Output noise level
(1) Perform measurement with no signal input.
Set the VOL1:MAX, VOL2:MIN, LINE/MIC:LINE,
THRU/MIX:THRU.
INPUT terminal 1 (XLR) is grounded through the
resistor of 100-150Ω, the noise level generated in the
output terminal is measured.
Confirm that the output noise level is within the
speci ed below.
CN304-1(OUTHF+) :
-62dBu or less
CN304-2(OUTHF-) :
(2) Perform measurement with no signal input.
Set the VOL1:MAX, VOL2:MIN, LINE/MIC:MIC,
THRU/MIX:THRU.
INPUT terminal 1 (XLR) is grounded through the
resistor of 100-150Ω, the noise level generated in the
output terminal is measured.
Confirm that the output noise level is within the
speci ed below.
CN304-4(OUTLF+) :
-46dBu or less
CN304-3(OUTLF-) :
(3) Perform measurement with no signal input.
Set the VOL1:MIN, VOL2:MAX, LINE/MIC:LINE,
THRU/MIX:MIX.
INPUT terminal 2 (XLR, PINS) is grounded through
the resistor of 100-150Ω, the noise level generated in
the output terminal is measured.
Confirm that the output noise level is within the
speci ed below.
CN304-1(OUTHF+) :
-62dBu or less
CN304-2(OUTHF-) :
JK601(OUTPUT) : -82dBu or less
2-16.
Residual noise level
Perform measurement with no signal input.
Set the VOL1:MIN, VOL2:MIN, LINE/MIC:LINE,
THRU/MIX:THRU.
The noise level generated in the output terminal is
measured.
Con rm that the output noise level is within the speci ed
below.
CN304-1(OUTHF+) :
-63dBu or less
CN304-2(OUTHF-) :
DBR15/DBR12
CN304-4(OUTLF+) :
-59dBu or less
CN304-3(OUTLF-) :
DBR10
CN304-4(OUTLF+) :
-61dBu or less
CN304-3(OUTLF-) :
2-15.
出力ノイズレベル
(1) 測定は入力無信号の状態で行います。
VOL1: 大、VOL2: 小、LINE/MIC:LINE、
THRU/MIX:THRU に設定します。
入力端子 1(XLR)を 100 150 Ωの抵抗を介し
て接地し、出力端子に発生するノイズレベルを
測定します。
出力ノイズレベルが下記の規定範囲内にあるこ
とを確認します。
CN304-1(OUTHF+) :
-62dBu以下
CN304-2(OUTHF-) :
(2) 測定は入力無信号の状態で行います。
VOL1: 大、VOL2: 小、LINE/MIC:MIC、
THRU/MIX:THRU に設定します。
入力端子 1(XLR)を 100 150 Ωの抵抗を介し
て接地し、出力端子に発生するノイズレベルを
測定します。
出力ノイズレベルが下記の規定範囲内にあるこ
とを確認します。
CN304-4(OUTLF+) :
-46dBu以下
CN304-3(OUTLF-) :
(3) 測定は入力無信号の状態で行います。
VOL1: 小、VOL2: 大、LINE/MIC:LINE、
THRU/MIX:MIX に設定します。
入力端子 2(XLR、PINS) 100 150 Ω
抗を介して接地し、出力端子に発生するノイズ
レベルを測定します。
出力ノイズレベルが下記の規定範囲内にあるこ
とを確認します。
CN304-1(OUTHF+) :
-62dBu以下
CN304-2(OUTHF-) :
JK601(OUTPUT) :-82dBu以下
2-16.
残留ノイズレベル
測定は入力無信号の状態で行います。
VOL1: 最小、VOL2: 最小、LINE/MIC:LINE、
THRU/MIX:THRU に設定します。
出力端子に発生するノイズレベルを測定します。
出力ノイズレベルが下記の規定範囲内にあることを
確認します。
CN304-1(OUTHF+) :
-63dBu以下
CN304-2(OUTHF-) :
DBR15/DBR12
CN304-4(OUTLF+) :
-59dBu以下
CN304-3(OUTLF-) :
DBR10
CN304-4(OUTLF+) :
-61dBu以下
CN304-3(OUTLF-) :

Other manuals for Yamaha DBR Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yamaha DBR Series and is the answer not in the manual?

Yamaha DBR Series Specifications

General IconGeneral
TypePowered Speaker
Amplifier ClassClass-D
InputsXLR, 1/4" TRS, RCA
OutputsXLR
Enclosure MaterialPlastic
Mounting OptionsPole mount
Coverage angle90° x 60°
I/O ConnectorsXLR, 1/4" TRS, RCA
Woofer Size12"
Tweeter Size1.4"
ProtectionOvercurrent protection

Related product manuals