110
Remote Function List
01X Owner’s Manual
Before Using Basics Section AppendixGetting Started Reference
■ SONAR: On the 01X, set Remote Select (page 87) in the Utility mode to “SONAR.”
Button Function LED
Notes
(page 114)
In all modes:
[NAME/VALUE]
Changes the indication of the parameter name and its value.
—
[SHIFT]+[NAME/VALUE]
Turns the Meter indication on or off.
— *19
DISPLAY [ / ] (Multi Channel)
Changes the parameter to be edited via a Knob in order one by one.
—
[PAGE SHIFT]+DISPLAY [ / ]
(Multi channel)
Changes the parameters to be edited via a Knob in groups of eight.
—
DISPLAY [ / ]
(SELECTED CHANNEL)
Changes the indicated parameter in order one by one.
—
[PAGE SHIFT]+DISPLAY [ / ]
(SELECTED CHANNEL)
Changes the indicated parameters in groups of eight.
—
[SHIFT]+[REMOTE]
Enters the mode for Multi Part Editor Remote operation. Press [REMOTE] button to can-
cel the mode.
flashes *5
[SEL] (in normal status)
Selects a channel.
lights/goes out *2
[SEL] ([SEL] flashes)
Fader touch-out (page 15)
flashes ➝
goes out
[SEL] ([AUTO EDIT] lights)
Fader touch-in (page 15)
flashes
[ON] (in normal status)
Turns each channel off or on (mutes/unmutes the signal).
lights/goes out *2, 32
[SHIFT]+[ON] (in normal status)
Turns all channels on.
lights *2, 32
[ON] ([SOLO] lights)
Sets Solo for each channel to on or off.
lights/goes out *2
[SHIFT]+[ON] ([SOLO] lights)
Sets Solo for all channels to off,
goes out *2
[ON] ([REC RDY] lights)
Sets the REC RDY of each channel to on or off.
lights/goes out *2
[SHIFT]+[ON] ([REC RDY] lights)
Sets the REC RDY of all channels to off.
goes out *2
[AUTO EDIT]
Changes the function of the [SEL] button to the touch-in function. This button flashes
during automation touch-in.
lights
[SOLO]
Changes the function of the [ON] button to the Solo function.
lights
[REC RDY]
Changes the function of the [ON] button to the REC RDY function.
lights
[AUTO R/W]+[ON]
This arms or activates fader automation.
lights *2
[AUTO R/W]+Knob
This arms or activates the parameters assigned to the respective knobs. (This is not indi-
cated on the 01X.)
—
[AUDIO]
Assigns a Track to a Fader.
—
[INST]
Assigns a Track to a Fader.
—
[MIDI]
Assigns a Track to a Fader.
—
[BUS/AUX]
Assigns an AUX BUS to a Fader.
—
[OTHER]
Assigns output level adjustment of the Virtual Main Bus to the Faders.
—
BANK [</>]
Scrolls through the track indication every eight channels.
—
[SHIFT]+BANK [</>]
Scrolls through the track indication channel-by-channel.
—
[FLIP]
Assigns the functions of the Channel Knobs to the Faders.
flashes
[FLIP] ➝ [FLIP]
Switches the functions of the Channel Knobs and the Faders.
lights
[EDIT]
Switches the current window.
—
[LOOP]
Sets Loop to on or off.
lights/goes out
[F1] – [F8]
[F1] – [F8] as defined in SONAR.
—
[SHIFT]+[F1]
The same as [F1] as defined in SONAR.
—
[SHIFT]+[F2]
The same as [F2] as defined in SONAR.
—
[SHIFT]+[F3]
The same as [F3] as defined in SONAR.
—
[SHIFT]+[F4]
Closes the current window.
—
[SHIFT]+[F5]
The same as [F5] as defined in SONAR.
—
[SHIFT]+[F6]
The same as [F6] as defined in SONAR.
—
[SHIFT]+[F7]
The same as [F7] as defined in SONAR.
—
[SHIFT]+[F8]
The same as [F8] as defined in SONAR.
—
[UNDO]
Executes the Undo operation.
—
[SHIFT]+[UNDO]
Executes the Redo operation.
—
[SAVE]
Executes the Save operation.
—
[WRITE]
Opens the window for entering the Marker to the current song position.
—
[MARKER]
Turns the Marker on or off.
—
[r]
Reverse (or Rewind). When the Marker is turned on, this operation moves the song posi-
tion to the previous Marker.
— *33
[SHIFT]+[r]
Moves the song position to the top of the song. When the Marker is turned on, this oper-
ation opens the window for entering the Marker.
—
To Next Page
Loading...
Need help?
General
