Why does my Yamaha F100DET Outboard Motor fuel management gauge show incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition may be wrong. To resolve this, default the engine number. Then, turn the key switch on in order from the portside engine to re-memorize each engine number.
Why is the illumination not lighting on my Yamaha F100DET Outboard Motor gauge?
If the illumination isn't lighting, it could be because of a power issue or a damaged gauge. You should try replacing the fuse, ensuring the couplers are securely connected, replacing any damaged wires or hubs, or replacing the gauge.
What to do if my Yamaha Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or replace the gauge itself.
What to do if Yamaha Outboard Motor fuel management gauge shows incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition might be wrong (especially for multi-applications). To fix this, default the engine number and turn the key switch on in order from the portside engine to re-memorize each engine number.
Why Yamaha F100DET boat speed and/or coolant pressure gauge does not show?
If the boat speed and/or coolant pressure gauge does not show, it is likely that the optional sensor has not been installed. Install the optional sensor.
What to do if Yamaha F100DET Outboard Motor trim gauge always shows fully tilted up position?
If the trim gauge always shows a fully tilted-up position, the trim sender signal is not being received. Connect the pink lead connectors to each other.
What causes Yamaha F100DET Outboard Motor gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
Why Yamaha Outboard Motor gauge operates unstably?
If the gauge operates unstably, it could be because a resistor is not connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs.
How to fix Yamaha F100DET Outboard Motor trim gauge showing incorrect position?
If the trim gauge shows an incorrect position, the initial position setting might be wrong, or the trim sender could be damaged. Put the motor in the fully trimmed-in position and reset the initial (zero) trim angle. If that doesn't work, replace the trim sender.
Why Yamaha F100DET Outboard Motor Speedometer or Comb. Speedometer & Fuel mgt gauge shows incorrect fuel level?
If the speedometer or combination speedometer & fuel management gauge shows an incorrect fuel level, the fuel sensor selection is likely wrong. Set up the fuel sensor to the correct resistance.
Procedures to prevent accidents, injuries, and ensure quality service.
Overall dimensions, weight, performance, and power unit details.
Specific maintenance values for engine components, lower unit, and electrical systems.
Specified and general torque values for fasteners.
Guideline for general maintenance intervals based on operating hours.
Procedures for checking compression pressure, oil pressure, and valve clearance.
Checks for ignition spark, wires, coils, ECM, sensors, and relays.
Checks for injectors, electric fuel pump, and relays.
Checks for fuses and starter relay.
Disassembly and checks for starter motor components.
Checks for stator coil and rectifier regulator.
Introduction to the diagnostic system and its functions.
Troubleshooting steps for power unit issues.
Diagnosing the electronic control system.
Wiring diagram for specific outboard motor models.
General| Max Output | 100 hp |
|---|---|
| Starting System | Electric |
| Lubrication System | Wet Sump |
| Cooling System | Water-Cooled |
| Full Throttle RPM Range | 5000-6000 RPM |
| Steering | Remote |
| Fuel Tank Capacity | External |
| Cylinder Configuration | In-Line |
| Fuel Induction System | Electronic Fuel Injection (EFI) |
| Ignition System | TCI (Transistor Controlled Ignition) |
| Recommended Fuel | Regular unleaded gasoline (min 87 octane) |
| Shaft Length | L (20") |
| Engine Type | 4-Stroke, DOHC, 16-Valve In-Line Four |
| Recommended Engine Oil | Yamalube 4M (10W-30 or 20W-40) |
To Next Page
