Why doesn't my Yamaha FL350AET Outboard Motor boat speed gauge show?
If the boat speed and/or coolant pressure gauge isn't showing, it means the optional sensor hasn't been installed. Install the optional sensor to fix this.
What to do if the Yamaha Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
Why Yamaha Outboard Motor illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
How to fix Yamaha FL350AET tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
What causes Yamaha FL350AET fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
Why does my Yamaha FL350AET Outboard Motor fuel management gauge show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting is probably wrong. Fill the tank with fuel, and then set the correct fuel tank capacity.
What to do if my Yamaha FL350AET Outboard Motor speedometer shows the incorrect fuel level?
If the speedometer shows an incorrect fuel level, the fuel sensor selection is likely wrong. You should set up the fuel sensor to the correct resistance.
What does it mean when my Yamaha Outboard Motor gauge shows “----”?
If the gauge shows “----”, it indicates that the digital signal is not being received. Make sure the couplers are securely connected and replace any damaged bus wires or hubs.
Why Yamaha FL350AET Outboard Motor boat speed and/or coolant pressure gauge does not show?
If the boat speed and/or coolant pressure gauge does not show, it is likely that the optional sensor has not been installed. Install the optional sensor.
What causes Yamaha Outboard Motor gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
Indicates a hazardous situation that could result in death or serious injury if not avoided.
Steps for safely removing the outboard motor from its shipping crate.
Instructions and considerations for correctly mounting the outboard motor on the transom.
Minimum water level relative to clamp bracket for 4-stroke engines.
Installation requirements and considerations for remote oil tanks.
Details specifications and types of Yamaha outboard propellers.
Guidelines for choosing the appropriate propeller based on engine and application.
Lists applications for standard propellers across different engine models and PS ratings.
Discusses throttle control systems (Push To Open/Pull To Open) and applicable models.
Details the features and specifications of the 703 side mount mechanical remote control.
Describes the 704 binnacle mount mechanical remote control for electric start models.
Explains the concealed mechanical remote control for electric start and runabout boats.
Describes the DEC binnacle mount remote control for electronic throttle and shift.
Details the concealed DEC remote control unit for electronic throttle and shift.
Details various wire harnesses for DEC systems, including dual station setups.
Introduces the multi-function tiller handle and its electrical functions.
Provides a wiring diagram for the 6X4 multi-function tiller handle for US models.
Procedures for installing gauges, including analog and digital types.
Details applications, models, and diagrams for analog tachometers.
Explains applications, models, and dimensions for digital tachometers.
Covers types, applications, dimensions, and tube routing for speedometers.
Details types, applications, dimensions, and setup for fuel management gauges.
Covers applications, dimensions, and adjustment for analog trim meters.
Details applications, dimensions, and attachment installation for coolant pressure meters.
Covers types, applications, dimensions, and sensor installation for coolant temp meters.
Provides representative wiring diagrams and wire color codes for remote controls and instruments.
Lists models compatible with digital network gauges, including engine types.
Instructions for initial setup of digital network gauges, including multi-sensor connection.
Table of common problems, causes, measures, and notes for gauge system issues.
Lists models compatible with digital network premium gauges.
Provides wiring diagrams for various single and dual station configurations.
Details battery specifications (CCA, MCA, RC, 20HR/IEC, JIS) for 4-stroke and 2-stroke engines.
Shows recommended battery cable lengths based on applicable models and conductor cross-section.
Explains wiring for isolator-equipped models and twin engine applications.
Checklist for pre-delivery inspection of outboard motors to enhance customer satisfaction.
Indicates a hazardous situation that could result in death or serious injury if not avoided.
Steps for safely removing the outboard motor from its shipping crate.
Instructions and considerations for correctly mounting the outboard motor on the transom.
Minimum water level relative to clamp bracket for 4-stroke engines.
Installation requirements and considerations for remote oil tanks.
Details specifications and types of Yamaha outboard propellers.
Guidelines for choosing the appropriate propeller based on engine and application.
Lists applications for standard propellers across different engine models and PS ratings.
Discusses throttle control systems (Push To Open/Pull To Open) and applicable models.
Details the features and specifications of the 703 side mount mechanical remote control.
Describes the 704 binnacle mount mechanical remote control for electric start models.
Explains the concealed mechanical remote control for electric start and runabout boats.
Describes the DEC binnacle mount remote control for electronic throttle and shift.
Details the concealed DEC remote control unit for electronic throttle and shift.
Details various wire harnesses for DEC systems, including dual station setups.
Introduces the multi-function tiller handle and its electrical functions.
Provides a wiring diagram for the 6X4 multi-function tiller handle for US models.
Procedures for installing gauges, including analog and digital types.
Details applications, models, and diagrams for analog tachometers.
Explains applications, models, and dimensions for digital tachometers.
Covers types, applications, dimensions, and tube routing for speedometers.
Details types, applications, dimensions, and setup for fuel management gauges.
Covers applications, dimensions, and adjustment for analog trim meters.
Details applications, dimensions, and attachment installation for coolant pressure meters.
Covers types, applications, dimensions, and sensor installation for coolant temp meters.
Provides representative wiring diagrams and wire color codes for remote controls and instruments.
Lists models compatible with digital network gauges, including engine types.
Instructions for initial setup of digital network gauges, including multi-sensor connection.
Table of common problems, causes, measures, and notes for gauge system issues.
Lists models compatible with digital network premium gauges.
Provides wiring diagrams for various single and dual station configurations.
Details battery specifications (CCA, MCA, RC, 20HR/IEC, JIS) for 4-stroke and 2-stroke engines.
Shows recommended battery cable lengths based on applicable models and conductor cross-section.
Explains wiring for isolator-equipped models and twin engine applications.
Checklist for pre-delivery inspection of outboard motors to enhance customer satisfaction.
General| Brand | Yamaha |
|---|---|
| Model | FL350AET |
| Category | Outboard Motor |
| Language | English |
To Next Page
