What to do if Yamaha Outboard Motor fuel management gauge shows incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition might be wrong (especially for multi-applications). To fix this, default the engine number and turn the key switch on in order from the portside engine to re-memorize each engine number.
Why Yamaha Outboard Motor gauge operates unstably?
If the gauge operates unstably, it could be because a resistor is not connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs.
How to fix Yamaha FL350AET Outboard Motor trim gauge showing incorrect position?
If the trim gauge shows an incorrect position, the initial position setting might be wrong, or the trim sender could be damaged. Put the motor in the fully trimmed-in position and reset the initial (zero) trim angle. If that doesn't work, replace the trim sender.
Why Yamaha FL350AET Speedometer or Comb. Speedometer & Fuel mgt gauge shows incorrect fuel level?
If the speedometer or combination speedometer & fuel management gauge shows an incorrect fuel level, the fuel sensor selection is likely wrong. Set up the fuel sensor to the correct resistance.
What to do if Yamaha FL350AET Outboard Motor gauge shows “----”?
If the gauge displays '----', it indicates that the digital signal is not being received. Check that the couplers are securely connected and replace any damaged bus wires or hubs.
What causes Yamaha FL350AET fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
How to fix Yamaha FL350AET tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
Why Yamaha Outboard Motor illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
What to do if the Yamaha Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
General| Brand | Yamaha |
|---|---|
| Model | FL350AET |
| Category | Outboard Motor |
| Language | English |
Indicates a hazardous situation that could result in death or serious injury if not avoided.
Steps for safely removing the outboard motor from its shipping crate.
Instructions and considerations for correctly mounting the outboard motor on the transom.
Minimum water level relative to clamp bracket for 4-stroke engines.
Installation requirements and considerations for remote oil tanks.
Details specifications and types of Yamaha outboard propellers.
Guidelines for choosing the appropriate propeller based on engine and application.
Lists applications for standard propellers across different engine models and PS ratings.
Discusses throttle control systems (Push To Open/Pull To Open) and applicable models.
Details the features and specifications of the 703 side mount mechanical remote control.
Describes the 704 binnacle mount mechanical remote control for electric start models.
Explains the concealed mechanical remote control for electric start and runabout boats.
Describes the DEC binnacle mount remote control for electronic throttle and shift.
Details the concealed DEC remote control unit for electronic throttle and shift.
Details various wire harnesses for DEC systems, including dual station setups.
Introduces the multi-function tiller handle and its electrical functions.
Provides a wiring diagram for the 6X4 multi-function tiller handle for US models.
Procedures for installing gauges, including analog and digital types.
Details applications, models, and diagrams for analog tachometers.
Explains applications, models, and dimensions for digital tachometers.
Covers types, applications, dimensions, and tube routing for speedometers.
Details types, applications, dimensions, and setup for fuel management gauges.
Covers applications, dimensions, and adjustment for analog trim meters.
Details applications, dimensions, and attachment installation for coolant pressure meters.
Covers types, applications, dimensions, and sensor installation for coolant temp meters.
Provides representative wiring diagrams and wire color codes for remote controls and instruments.
Lists models compatible with digital network gauges, including engine types.
Instructions for initial setup of digital network gauges, including multi-sensor connection.
Table of common problems, causes, measures, and notes for gauge system issues.
Lists models compatible with digital network premium gauges.
Provides wiring diagrams for various single and dual station configurations.
Details battery specifications (CCA, MCA, RC, 20HR/IEC, JIS) for 4-stroke and 2-stroke engines.
Shows recommended battery cable lengths based on applicable models and conductor cross-section.
Explains wiring for isolator-equipped models and twin engine applications.
Checklist for pre-delivery inspection of outboard motors to enhance customer satisfaction.
To Next Page
